Korg KingKORG NEO Manual Del Usuario página 13

4 .
Connecting a MIDI device or computer
You'll need to make these connections if you want to use the
KingKORG NEO's keyboard or controllers to control an external
MIDI sound module or to use a different MIDI keyboard or a
sequencer to control the KingKORG NEO's sound generator. (PG:
"7. MIDI parameters")
5 .
Connecting the AC adaptor
Connect the included AC adapter to the DC12V jack located on the
rear panel. Loop the cable around the cord hook on the rear panel of
the KingKORG NEO, so that the cable doesn't get accidentally
pulled out. Be careful not to apply more force than necessary to the
DC plug.
You must use the included AC adaptor. Using a different AC
adaptor may cause malfunctions.
Be sure that the AC outlet provides the correct voltage for your
AC adaptor.
Turning the power on/off
1 .
Turning the power on
Before you power-on the KingKORG NEO, you must power-off
any external output device such as your powered monitor
speakers.
1.
Turn the KingKORG NEO's VOLUME knob all the way to the
left to minimize unwanted audio artifacts during startup.
2.
Long-press the power switch. Once "KingKORG NEO"
appears in the display, take your finger off the switch.
Once the instrument turns on, the program number and name
appear in the main display.
3.
With the volume lowered on your monitor speakers or other
external output system, turn on the power of your output system.
4.
Slowly raise the KingKORG NEO's VOLUME knob while you
adjust the volume of your output system.
2 .
Turning the power off
Never turn off the power while data is being saved. Doing so
may cause the KingKORG NEO's data to be damaged.
1.
Lower the volume of your monitor speakers or other external
output system, and turn off the power of your output system.
2.
Turn the KingKORG NEO's VOLUME knob all the way to the
left, and press and hold the power switch until the main
display goes blank.
Auto power-off
The KingKORG NEO has an auto power-off function. When a certain
duration of time has elapsed without user input on the front panel
buttons or knobs, or without the keyboard being played, the power will
turn off automatically. With the factory settings, this is set to four hours.
If desired, you can disable this function as follows.
1 .
Disabling the auto power-off function
1.
Hold down the SHIFT/EXIT button and press the PROGRAM
(GLOBAL) button to enter Global mode.
2.
Use the PAGE +/− buttons to access the GLOBAL "g14: Power
Off" page.
Playing the KingKORG NEO
3.
Turn the value dial to choose "Disable."
4.
Press the WRITE button to save the global settings. (OM:
p.21 "1. Saving global settings")
If you turn off the power without saving, the changes you've
made to the global settings will be discarded. If you want to
use your edited settings in the future, be sure to save them.
Playing the KingKORG NEO
Selecting and playing a
program
1 .
Display screen
Main display (when playing a program)
When the PROGRAM (GLOBAL) button is lit up, the main display
will show the program number and program name.
When the FAVORITES button is lit up, the display will show the
bank, program number and program name.
When the PROGRAM (GLOBAL) button is lit
When the FAVORITES button is lit up
Program
number
Main display (when editing a program)
The display will show the page number, page name, parameter
name, and value. The same contents will also be shown in the
display when editing global settings (when the PROGRAM
(GLOBAL) button is blinking).
Page number
Parameter name
OSCILLATOR sub display
The display will show information about the currently selected
oscillator.
FILTER sub display
The display will show information about the currently selected filter.
Program
number
Program
name
Bank
Program
name
Page name
Parameter value
Oscillator type number
Oscillator type name
Filter type number
Filter type name
13