Publicidad
Idiomas disponibles
Idiomas disponibles
Problem
Possible Cause
Tool operates,
Low battery charge or
but does
damaged battery.
not drive the
fastener fully.
Depth adjustment set
too shallow.
Tool not firmly applied
to workpiece.
Material and fastener
length too rigorous an
application.
Maintenance
Your STANLEY corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool/appliance care and regular cleaning.
Warning! Switch off and unplug the appliance before carrying
out any cleaning.
Dirt and grease may be removed from the exterior of the
u
appliance using a cloth.
Warning! NEVER use solvents or other harsh chemicals
for cleaning the non-metallic parts of the appliance. These
chemicals may weaken the materials used in these parts. Use
a cloth dampened only with water and mild soap. Never let
any liquid get inside the unit; never immerse any part of the
unit into a liquid.
Warning! NEVER spray or in any other way apply lubricants
or cleaning solvents inside the tool. This can seriously affect
the life and performance of the tool.
Service Notes
This product is not user serviceable. There are no user
serviceable parts inside the nailer. Servicing at an authorized
service center is required to avoid damage to static sensitive
internal components.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
32
Possible Solution
Charge or replace battery.
Rotate depth adjustment
wheel to
a deeper setting.
Read instruction manual.
Choose appropriate material
or fastener length.
Voltage
Battery Type
Actuating mode
Magazine angle
No load speed
Drive energy
Weight (bare tool)
Fasteners
Length
mm
Shank diameter
mm
Angle
This tool is a Bare unit but can be used with the chargers in
the following table.
Charger
SC125
AR, B2 220V
Input
B3
120V
V
Voltage
BR
BIVOLT
AC
(127V | 220V)
Output
18V
Volt-
V
(20V MAX)
DC
age
Current A
1.25
This tool is a Bare unit but can be used with the batteries in
the following table.
Battery
SB201
18V
Voltage
V
(20V MAX)
DC
Capacity
Ah
1.5
Type
Li-Ion
Service Information
STANLEY offers a full network of company-owned and author-
ized service locations. All STANLEY Service Centers are
staffed with trained personnel to provide
customers with efficient and reliable power tool service. For
more information about our authorized service centers and if
you need technical advice, repair, or genuine factory replace-
ment parts, contact the STANLEY location nearest you or visit
us at www.stanleytools-la.com.
SCN618 Type:1
18 V (20 V Max)
V
DC
Sequential
/min
approx
kg
16 - 50
1.27
Straight
SC200
SC400
SC120
AR, B2 220V
AR, B2 220V
AR, B2 220V
B3
120V
B3
120V
B3
BR
127V
BR
127V
BR
(127V | 220V)
18V
18V
(20V MAX)
(20V MAX)
(20V MAX)
2
4
SB202
SB204
18V
18V
(20V MAX)
(20V MAX)
(20V MAX)
2.0
4.0
Li-Ion
Li-Ion
Li-Ion
Straight
9000
50 J
2.43
120V
BIVOLT
18V
1.25
SB206
18V
6.0
Li-Ion
Publicidad
