Publicidad
OWNER'S MANUAL BIKE FULL-FACE HELMETS
Thank you. You have chosen a TSG safety product designed especially for action sport athletes.
Please read the following information carefully. Correctly used and cared for, it will keep you bet-
ter protected and satisfied.
TESTING, APPROVAL & USE
This helmet is intended for bicycle use only and not for motorized vehicle use including motor-
cycles or mopeds! This helmet is designed to protect impact caused by falling or ejected objects
and collision of parts of the body with an obstacle.
This helmet complies with the Personal Protective Equipment Regulation (EU) 2016/425 and pass-
es EN 1078+A1:02.2013: Helmets for pedal cyclists and for users of skateboards and roller skates.
This helmet has passed EN 1078:2012+A1:2012 to show conformity to the EHSR (Essential Health
and Safety Requirements ) of Regulation (EU) 2016/425 (as brought into UK law and amended).
The helmet also complies with ASTM F1952: Standard Specification for Helmets used for Down-
hill Mountain Bicycle Racing.
The helmet complies with CPSC 16 CFR 1203 16 CFR 1203 (Consumer Product Safety Commis-
sion) Safety Standard for Bicycle Helmets for Adults and Children Age 5 and older.
Find the declaration of conformity for each model on our website:
www.ridetsg.com/service/declaration-of-conformity
WARNING NOTICES – WARNING!
• For maximum protection the helmet must be fitted and attached properly to the wearer's
head in accordance with the manufacturer's fitting instructions.
• This helmet is designed to absorb shock by partial destruction of the energy absorbing
liner. This damage may not be visible to the user. Therefore, if subjected to a severe impact
or blow, the helmet should be destroyed and replaced even if it appears undamaged.
• A helmet can only provide a level of protection for areas that it covers.
It does not protect your neck.
• A helmet can only protect if it fits well and properly to your head and if it is correctly buckled.
• No helmet can protect against all possible impacts.
• Do not modify or remove any of the original component parts of the helmet other than as
recommended by the manufacturer, as it may affect its protective capacity. The helmet must
not be modified to attach accessories in a manner not recommended by the manufacturer.
Do not remove the original stickers on the inside of the helmet.
• Some common substances can cause damage to the helmet, though it may not be visible to
the user. The use of any solvents, transfers, adhesives, paints or cleaning solutions can cause
damage to the helmet and make it ineffective in the result of an accident.
• This helmet is for pedal cyclists, skate boarders and roller skaters. ATTENTION! Not for motor
vehicle use.
• Warning! This helmet should not be used by children while climbing or doing other activities
when there is a risk of strangulation/hanging if the child gets trapped with the helmet.
6 – ENGLISH
CLEANING
Wipe only with a soft damp cloth in gentle soap or mild detergent in cold water, rinse by wiping
with a soft cloth damped in cold water and dry with a soft cloth. Comfort padding and cheek
pads can be removed and hand washed and air dried.
STORAGE AND TRANSPORTATION
After each use, allow your helmet to air dry and then store in a cool, dry place. Do not expose
your helmet to impact or external force during transport. Helmets will be damaged if exposed
to temperatures exceeding 65°C. Vehicles and storage bags can exceed this on very hot days.
Heat damaged helmets will have random disfigured areas where the texture appears bubbly
and uneven. If damaged, helmets should be destroyed and replaced immediately.
MAINTENANCE AND OBSOLESCENCE
For maximum performance, your TSG product must be inspected prior to each use. Stop
using the helmet if any components show signs of damage or are worn, cracked, and/or de-
formed, or if the inside foam has deteriorated. Helmets have a limited life span in use and
should be replaced every 3-5 years under normal use conditions, but at the latest after 8
years from date of manufacture (see product label). If you know or suspect that your helmet
has been damaged or exposed to any abnormal force, destroy, and replace it. Please dispose
of it in an environmentally-friendly manner. Do not make any modifications to the helmet, this
includes the outer shell, the inner EPS li-ner or chin strap, any modifications will void all war-
ranties and affect the helmet's performance.
FITTING INSTRUCTIONS
In order to fulfill its protective function, your helmet must be perfectly adjusted to your head.
Measure your head at its widest point, compare it to the sizing chart available on a label inside
the helmet, and try on several sizes until you find the correct fit that stays on comfortably,
steadily and securely.
1. Put on the helmet in a manner so that it sits straight on your head and covers your forehead,
without blocking your vision. It is important that the helmet can neither ride up your forehead nor
be pushed down over your eyes. The helmet should fit comfortably; so that it holds onto your head
as you move it front and back, as well as side-to-side (FIG. 1).
2. The comfort pads inside the helmet should exert firm, even, but comfortable pressure against
your head. The helmet fits well if the pads are in contact with all sides of your head around the
helmet's interior. A helmet that fits well also fits comfortably without being too tight.
3. When you are satisfied with the fit, tighten the chin strap. The chin strap should be as tight as
possible but without causing pain. Never wear your helmet with the buckle unfastened. Helmet
adjustment can change during riding and storage. Check the helmet for proper adjustment and
fit prior to each bicycle ride
Never wear your helmet with the buckle unfastened. Helmet adjustment can change during riding
and storage. Check the helmet for proper adjustment and fit prior to each bicycle ride.
ENGLISH – 7
Publicidad
