Gaggenau CV282101 Instrucciones De Montaje página 18

Flush installation
With the flush installation, the appliance and worktop
are on one level. There is no unattractive stepping
between the appliance and the worktop.
You can install the appliance in the following
temperature-resistant and waterproof worktops:
Stone worktops
¡
Plastic worktops, e.g. Corian®
¡
Solid wood worktops
¡
Installation in compressed-wood worktops is not pos-
sible.
Preparing the units
Requirement: The fitted units are heat-resistant up to
90 °C.
Mark the unit cut-out in accordance with the in-
1.
stallation diagram.
→ Fig.
15
Drill four holes with a diameter of 6 mm.
2.
→ Fig.
26
Ensure that the angle of the cut surface to the
3.
worktop is 90°.
→ Fig.
26
Observing the minimum clearances when in-
stalling above a drawer
When removing the overflow container on integ-
1.
rated appliances, take the minimum clearances
into consideration.
→ Fig.
12
Observe the position of the overflow container.
2.
→ Fig.
13
Preparing the unit for circulating-air mode with the
adapter
Notes
When installing directly on an outer wall that is not
¡
thermally insulated or above a cold floor
(µ ≥ 0.5 W/m² °C), we recommend a configura-
tion with a circulating-air duct.
Air outlets must not be directed at other appli-
¡
ances, they should be parted by a separation
panel. If you cannot install any separation panels,
refer to other installation types..
Observe the relevant dimensions when combining
1.
with the adapter for the cut-out in the back wall.
→ Fig.
27
Use the template to create the cut-out in the back
2.
wall.
In circulating-air mode, establish an air outlet in
3.
the unit's plinth.
Provide a minimum air outlet cross-section of
‒
approx. 400 cm².
Make the outlet opening in the base panel as
‒
large as possible in order to keep draughts and
noise to a minimum.
Make the outlet opening by shortening the
‒
plinth or by using suitable ventilation grilles or a
lamellar plinth.
To guarantee that the appliance works correctly,
4.
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
After making the cut-outs, remove any shavings.
5.
Seal the cut surfaces so that they are heat-resist-
6.
ant and waterproof.
→ Fig.
26
18
Preparing the unit for circulating-air mode with a
circulating-air duct
If required, remove the unit's back wall.
1.
Observe the relevant dimensions when combining
2.
with the AD 857 030 flat duct elbow for the cut-
out in the back wall.
→ Fig.
28
In circulating-air mode, establish an air outlet in
3.
the unit's plinth.
Provide a minimum air outlet cross-section of
‒
approx. 400 cm².
Make the outlet opening in the base panel as
‒
large as possible in order to keep draughts and
noise to a minimum.
Make the outlet opening by shortening the
‒
plinth or by using suitable ventilation grilles or a
lamellar plinth.
To guarantee that the appliance works correctly,
4.
ventilate the hob appropriately via an air outlet
with a minimum cross-section of 200 cm² in the
base unit.
After making the cut-outs, remove any shavings.
5.
Seal the cut surfaces so that they are heat-resist-
6.
ant and waterproof.
→ Fig.
26
Preparing the unit for air extraction mode
If required, remove the unit's back wall.
1.
Observe the relevant dimensions when combining
2.
with a flat duct elbow for the cut-out in the back
wall.
→ Fig.
29
After making the cut-outs, remove any shavings.
3.
Seal the cut surfaces so that they are heat-resist-
4.
ant and waterproof.
→ Fig.
26
Attaching adhesive tape
Attach the enclosed adhesive tape to the worktop
▶
section.
→ Fig.
30
Installing the appliance
WARNING ‒ Risk of injury!
Parts that are accessible during installation may
have sharp edges and may lead to cutting injuries.
Wear protective gloves.
▶
The appliance is heavy.
To move the appliance, two people are required.
▶
Use only suitable tools and equipment.
▶
Install the appliance for air extraction mode
▶
→ Page 19, circulating-air mode → Page 18 or
circulating-air mode with circulating-air duct
→ Page 19.
Note: The appliance is only intended for flush install-
ation.
Installing the appliance for circulating-air mode
with adapter
For the circulating-air mode, use the adapter and
1.
the odour filter.
Ensure that the clearance between the appliance
2.
and the rear panel of the unit is between 10 and
80 mm.
Attaching the adapter
Clean and degrease the adhesive surface around
1.
the cut-out in the unit's back panel.
Insert the adapter into the outlet opening on the
2.
rear of the hob.
→ Fig.
31