Publicidad
Idiomas disponibles
Idiomas disponibles
* = may not be included in the scope of delivery!
8.1
Fitting the front handle (5) (Fig. 1-3)
Fit the front handle (5) to the tubular shaft (4):
1. Firstly, loosen the Allen screws M5 (5b) and remove
the rubber ring (5a) on the front handle (5). Use the 4
mm Allen key (A).
2. Place the rubber ring (5a) onto the tubular shaft (4).
3. Attach the leg guard (6) to the bottom of the rubber
ring (5a).
Make sure that the rubber ring (5a) is seated in the re-
cess on the leg guard (6).
4. Place the front handle (5) on the rubber ring (5a) from
above so that the screw holes of the leg guard (6) and
the front handle (5) are on top of each other.
5. Secure the front handle (5) with the four Allen screws
M5 (5b). Use the 4 mm Allen key (A).
Ensure that the leg guard (6) is fitted to the left (to-
wards the operator).
8.2
Fitting the protective covers (21/24)
(Fig. 1, 4)
DANGER
Danger of injury!
If an incompletely assembled product is used, serious
injuries can be caused.
–
Do not use the product until it has been fully fitted.
–
Before each use, carry out a visual inspection to
check that the product is complete and does not
contain any damaged or worn components. Safety
and protective devices must be intact.
1. Attach the two protective covers (21/24) to the holder
provided on the front tubular shaft (20).
2. Fasten the two protective covers (21/24) with the two
M6 Allen screws (20a). Use the 5 mm Allen key (B).
8.3
Assembling/disassembing coil
capsule (23) (Fig. 1, 5-7)
The front brush cutter/grass trimmer tubular shaft (20) can
be used as a grass trimmer with the coil capsule (23).
1. Remove the M10 nut (31) and the cover (30) from the
mounting spindle (33). Attention - Left-handed thread!
Use the installation spanner (D).
2. The M10 nut (31) and the cover (30) are not required
for installation of the coil capsule (23).
The inner flange (34) and the spring washer (32) re-
main on the mounting spindle (33).
3. Hold the inner flange (34) through the outer flange
(35) using a 5 mm Allen key (B).
4. Turn the coil capsule (23) anti-clockwise onto the
mounting spindle (33) and fasten the coil capsule (23)
to the mounting spindle (33) hand-tight.
5. Removal of the coil capsule (23) takes place in re-
verse order.
Note that the direction of rotation of the coil capsule (23)
must match with the direction of the arrow on the protec-
tive cover (21) (Fig. 4).
40 | GB
8.4
Fitting/removing cutting blade (25)
(Fig. 1, 8, 9)
The front brush cutter / grass trimmer tubular shaft (20)
can be used as a brush cutter with the cutting blade (25).
1. Remove the M10 nut (31), the cover (30) and the
spring washer (32) from the mounting spindle (33). At-
tention - Left-handed thread! Use the installation
spanner (D).
2. The internal flange (34) remains on the mounting spin-
dle (33).
3. Place the cutting blade (25) on the internal flange
(34).
Note that the direction of rotation of the cutting blade
(25) must match with the direction of the arrow on the
protective cover (21) (Fig. 4).
4. Then push the spring washer (32) and the cover (30)
onto the mounting spindle (33).
5. Fasten the cutting blade (25) with the M10 nut (31).
6. Tighten the M10 nut (31) with the installation spanner
(D). To do this, hold the inner flange (34) through the
outer flange (35) using the 5 mm Allen key (B).
7. Remove the blade guard (27) from the cutting blade
(25).
8. Removal of the cutting blade (25) takes place in re-
verse order.
8.5
Fit the chainsaw guide bar (14) and
saw chain (15) (Fig. 1, 10-13)
WARNING
Danger of injury when handling the saw
chain or the blade!
–
Wear cut-resistant gloves.
ATTENTION
Blunt blades overload the product! Do not use the prod-
uct if the cutters are faulty or heavily worn.
Notes:
• A new saw chain stretches and needs to be re-ten-
sioned more often. Check and adjust the chain ten-
sion regularly after each cut.
• Only use saw chains and blades designed for this
product.
CAUTION
An incorrectly installed saw chain leads to uncontrolled
cutting behaviour by the product!
When fitting the saw chain, observe the prescribed run-
ning direction!
1. Turn the fastening nut (36) anti-clockwise, so that the
chain wheel cover (37) is removed. Use the open-end
spanner AF 8/10mm (C).
2. Turn the chain tensioning screw (38) anti-clockwise to
loosen the chain tension. Use the installation spanner
(D).
www.scheppach.com
Publicidad
