Publicidad
Idiomas disponibles
Idiomas disponibles
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
DANGER
Danger of injury!
If the product is jammed, do not try to pull the product
out by using force.
–
Switch off the engine.
–
Use a lever arm or wedge to get the product free.
WARNING
Check the safety equipment regularly before each start-
up. Faulty safety equipment can cause serious injuries!
10.1
Switching the product on/off (Fig.
1)
WARNING
Danger of injury due to kickback!
–
Never use the product one-handed!
Notes:
The speed can be steplessly controlled by the on/off
switch. The further you press the on/off switch, the higher
the speed.
Before switching on, make sure that the product does not
touch any objects.
When using the brush cutter (20):
1. Remove the transport guard (26) from the cutting
blade (25).
When using the hedge trimmer (17):
1. Pull the blade guard (27) off the cutter bar (19).
When using the pole-mounted pruner (13):
1. Check that there is saw chain oil in the oil tank (16).
2. Fill in saw chain oil before the oil tank (16) is empty,
as described under 9.1.
3. Pull the blade and chain guard (28) off the chainsaw
guide bar (14).
The speed can also be changed during operation.
You can choose between 3 speed settings:
Slow
Medium
Switching on
1. Press the main switch (10) until the LED lights up.
2. Select the speed setting.
3. Hold the front handle (5) with your left hand and the
rear handle (2) with your right hand. Thumb and fin-
gers must firmly grasp the handles (2, 5).
4. Grasp the switch-on lock (11) on the rear handle (2).
5. Press and hold the switch lock (11).
6. To switch on the product, push the on/off switch (3)
with your thumb.
Notes:
It is not necessary to keep the switch lock pressed after
starting the product. The switch lock is intended to pre-
vent accidental starting of the product.
If the product is not used, the LED on the main switch re-
mains lit for 1 minute. The product is then switched off au-
tomatically.
Switching off
1. To switch it off, simply release the on/off switch (3).
2. Press the main switch (10) until the LED goes out.
3. Put on the supplied transport guard (26), blade and
chain guard (28) and blade guard (27) after every time
you work with the product.
10.2
In the event of overloading, the battery will switch itself
off. After a cool-down period (time varies), the product
can be switched back on again.
11 Working instructions
DANGER
Danger of injury!
This section examines the basic working technique for
using the product.
The information provided here does not replace the ma-
ny years of training and experience of a specialist.
Avoid any work that you are not adequately qualified
for!
Careless use of the product can lead to serious injuries
and even death!
CAUTION
After switching off, the product will run on. Wait until the
product has come to a complete stop.
Notes:
Before switching on, make sure that the product does not
touch any objects.
Some noise pollution from this product is unavoidable.
Postpone noisy work to approved and designated times. If
necessary, adhere to rest periods.
Only process free, flat surfaces with the tool attachment.
Carefully inspect the area to be cut and remove all foreign
objects.
Avoid bumping into stones, metal or other obstacles.
The tool attachment could be damaged and there is a risk
of kickback.
Fast
• Wear prescribed protective equipment.
• Ensure that other people remain at a safe distance
from your workspace. Anyone who enters the
workspace must wear personal protective equip-
ment. Fragments of the workpiece or broken accesso-
ry tools can fly off and cause injury – even outside the
immediate working area.
www.scheppach.com
Overload protection
GB | 43
Publicidad
