Publicidad
Idiomas disponibles
Idiomas disponibles
Description
Fuzzies, (pair)
Foot Strap, Cotton, 24" quick link
Foot Strap, Cotton, 27" quick link
Belly Strap
Wood, Roll Down Bar, 23" Outside Hooks
Cotton Web, CL
Trapeze Sling, CL
Loops, Single Dring, CL (pair)
safety Strap, CL
Wing Knob
Sliding PTB, Wood, CL
Shoulder Bolt, Sliders
Spring, Trap, Green
Spring, Trap, Red
Spring, Trap, Blue
Spring, White
Spring, Trap, Grey, CL
Spring Trap, Long Red
Bottom Frame w/Mat Assembly
Trapeze CL Canopy Top Assembly
Vertical Slider Assembly, CL
Trapeze Bar Assembly
PTB Slider Assembly
Head End SS Tubes
Foot End SS Tubes
Wrench, 21mm x 1/2"
1/8" Cotter Pin
3/16" Allen Wrench
ASSEMBLY
» Using the provided 3/16" allen wrench, loosen the set screws
in each of the eight flange connectors mounted to the outside
of the frame. Remove the two vertical tubes from the box and
the sliding push thru bar system. Lay the tubes down so the
holes on the sides of the tubes face away from each other.
Take the sliders of the push thru bar (PTB) and slide them over
the tubes opposite the end with the eye bolts, you will need
to pull the knobs of the sliders out to move the sliders up the
tubes. Continue to move the sliders up the tubes until the
pins lock into the bottom set of the three holes in the tube.
Make sure both sliders are locked into the same bottom holes.
Insert the provided cotter pins into each of the 1/8" holes near
the bottom ends of the tube. Pick up this assembled tube
set, be careful of the PTB, it may swing; place the assembly
in the flanges on the head end of the machine (the end with
the vinyl flaps). Be carefully of the cotter pins so they do
not scratch the vinyl or wooden frame. The cotter pins will
automatically set the tubing height.
Insert the provided cotter pins into each of the 1/8" holes near
the bottom ends of the other two vertical tubes. Pick up the
tube assembly with the vertical slider and place the tube ends
into the flanges on the foot end of the frame.
02
» With help, place the rectangular section on top of the vertical
Part #
Qty
tubes. Make sure all 4 corner fittings fit securely onto the
101-022
1
tubes.
607-548
1
Note: Set the rectangle on the vertical tubes so that the safety
210-130
1
210-034
1
strap and the push-thru bar are on the same end.
607-127
1
607-330
2
» Using the 3/16" allen wrench, tighten the set screws in the
607-331
1
corner fittings and in the flanges around the frame. After
607-346
1
tightening all set screws in all the corner angles, test the
607-355
1
movement of the sliding push thru bar. To do this pull the
GEN9371
4
knobs of the sliders out and start sliding the PTB up or down.
607-461
1
This system should move easily and not stick when uniform
619-203
2
pressure is applied on each side. If the sliders stick when
SPR9000
1
moving the position, simply loosen the set screws that are
SPR9001
1
holding the vertical poles, rotate the tubes as necessary until
SPR9004
2
the sliders move freely. Be sure to re-tighten all set screws.
SPR9238
2
Remove the cotter pins from the tubes and save for future
SPR9245
2
use.
SPR9246
2
N/A
1
N/A
1
HOW TO ADJUST YOUR SLIDING PUSH THROUGH BAR
N/A
1
17803
1
Position your hands on the outside of each slider. Place your middle
N/A
2
and/or ring fingers under the silver base of the knob; right where the
TRP0110
2
black body of the knob threads into. Place your index finger and thumb
TRP0111
2
around the knob itself. Pull each of the knobs outwards, away from the
ALL0060
1
vertical tubes, until they stop. Using the same force on each arm, move
216-000
4
the slider upwards or downwards to each new location. Once you near a
GEN9280
1
new location slightly release the outward pull of the knobs. The pins will
automatically fall into the next position when aligned.
WEEKLY MAINTENANCE
Inspect springs for separations, and replace if needed. Inspect
snaps on springs and make sure the retractors operate smoothly.
Replace them if worn or they do not operate freely. Make sure
that there are no indentations on the inside of the hooks. Inspect
all nuts, eyebolts and setscrews for tightness. Tighten or replace
if necessary.
It is recommended to check to ensure the pins in the plunger
knobs protrude and lock into the vertical tubes. First pull both
knobs out and start moving the sliders to a different position.
Release the knobs before the next hole and continue to slide the
system. Once over a hole the pin of the knob will drop into the
opening. Once each slider is in a new position apply a down force
on the PTB directly downwards. The pins of the sliders should
not come out of the holes. If the pins do not stay in the tube
holes, the pull knobs need to be replaced; call Balanced Body for
replacement parts.
QUESTIONS?
Call Balanced Body at 1-800-PILATES (1-800-745-2837) or
916-388-2828.
Publicidad
