Publicidad
Idiomas disponibles
Idiomas disponibles
9
Alarm functionality
Set an alarm
NOTE: Check that the micro system is displaying the correct time and date
before you set an alarm.
Scan setting
Audio setting
FM
AMS
System
BT
System
Alarm
Alarm 1 Setup
Alarm 2 Setup
Time
Duration
Source
Frequency
Volume level
Alarm
NOTE: If the time is not set or has failed to update from the radio signal,
<Time is not set> will be displayed when you try to set the alarm. The micro
system will then prompt you to set the time. An alarm can only be set after
the time has been set.
Stop, snooze or switching the alarm off
To stop the alarm, short press
alarm symbol will remain in the display and will sound again at the same
time the next day unless it was set for <Once>.
To snooze the alarm, press
. <Snooze> will be displayed, followed
by a 10-minute countdown. Once the countdown ends, the alarm will
sound again. You can terminate snooze by pressing
be displayed.
To switch off the alarm, follow the steps for 'Set an alarm' and select
<Off>.
Sleep timer
You can set your micro system to switch to standby mode automatically
using the sleep timer. You can choose from Sleep off, 10, 15, 30, 45 and
60 minutes. To do this, long press
<System> / <Sleep>. Use
<Sleep> will be displayed. In the top right of the micro system display,
the number of minutes until your micro system will switch to standby
mode will be displayed e.g., S90.
Display backlight timeout
To adjust the display backlight timeout, long press
to scroll to and select <System> / <Backlight> / <Timeout>. Scroll
through the available backlight timeout options. The current setting will
have an asterisk (*) in the display. Press
Similarly, use
to change the settings for the backlight brightness
for the <Dim level> and <On level>. There are 3 options available:
<High>, <Medium>, and <Low>.
Display language
To change the display language, long press
and select <System> / <Language>. Use
System
Sleep
Alarm
Equaliser
Time
Backlight
Language
Factory reset
Software Version
Alarm 1 or 2 settings
Hour
Min
1, 5, 10, 15, 30, or 60 minutes
Buzzer or FM
Daily, once, weekdays or weekends
25%-100%
On or Off
,<Alarm off> will be displayed. The
. <Alarm off> will
. Use
to scroll and select
to scroll and select your preference.
. Use
to select.
. Use
to scroll and select
your preferred language. There are 7 options available: English, French,
German, Italian, Spanish, Polish, and Dutch. An asterisk (*) will be
displayed next to the current language setting.
Software version
To check the software version of your micro system, long press
to scroll and select <System> / <SW Version>. The software
version will be displayed.
Factory reset
You can reset your micro system to restore it to the original factory
settings.
NOTE: If you reset your micro system, your stored presets will be deleted and
any connected Bluetooth device will be unpaired.
Long press
reset>. <Factory Reset? <No> Yes> will be displayed. Use
scroll and select <Yes>. <Restarting...> will be displayed. After a few
seconds, the display will change to <SHARP sharpconsumer.eu> and
will then go to standby mode.
Troubleshooting
If there is no sound or power:
• Adjust the volume.
• Check that the power cable is connected and that the micro system is
not in standby mode.
• If you have headphones connected, audio will play through them.
Unplug your headphones to listen through the micro system speakers.
• Ensure you are in the correct mode, and using the correct control
functions for that mode.
• If you are using a Bluetooth connected device or an external sound
source via Aux-in, increase the volume on the secondary device and on
the micro system.
If the radio reception is poor:
Make sure that you have fully extended the aerial.
Rescan for radio stations, see section 'Tune to an FM station' .
Try moving your micro system to another location to see if the reception
improves.
Check that you do not have other electrical equipment close to your
micro system. This may cause interference.
If a CD does not play:
• Check that you are in CD mode.
• Remove the CD and check that it is not scratched or damaged as this
will not play.
• Please check that you are using an original audio CD and not a copy. If
the CD is not an original, playback may not be supported (depending
on the CD and audio file types being used).
If you are unable to pair with a Bluetooth device:
Check that you are in Bluetooth mode.
Ensure that you are within 10 metres of the micro system for Bluetooth
functionality.
Move the micro system and Bluetooth device away from other Bluetooth
devices/electrical equipment.
If possible, turn off other nearby Bluetooth devices or disable their
Bluetooth functionality.
If the function buttons do not respond:
• Check that the mains power is connected at the back of your micro
system. Short press the
• Try to reset to factory default settings. See 'Factory reset' section.
NOTE: All of your settings, including the radio station list, connected
Bluetooth devices and any presets will be deleted when you reset the micro
system.
to scroll
. Use
to scroll and select <System> / <Factory
(Power/Mode) button.
. Use
to
Publicidad
