Descargar Imprimir esta página

Simplicity Duke SYC102 Manual Del Usuario página 75

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 297
3
PREPARATION FOR PUTTING INTO OPERATION
This chapter primarily serves the needs of the vendor's mechanics that prepare the mower for the user within the scope of pre-sale
service.
In the event that you have received your mower already assembled and ready for operation, please skip directly to chapter 4.
In the event that you have unpacked the mower yourself, then it is necessary to prepare it for operation according to the instructions
contained in this chapter. In the event that you are unsure about the procedure or you have insufficient equipment, tools or experience,
please do not hesitate to contact the vendor of the mower for assistance.
We recommend performing all assembly works in a team of at least two people.
3.1
UNPACKING AND INSPECTING THE CONTENTS
The riding mower is supplied on a wooden pallet in a package made from wooden boards. Assemblies that had to be removed for
transportation reasons are packaged in individual packages.
Inspect immediately after delivery that the riding mower has not been damaged. In the event of damage inform the carrier. If the
complaint is not lodged in time, no potential demands can be claimed.
Check that the mower model is the same as you ordered. In the event of an irregularity do not unpack the mower and immediately
report this discrepancy to the supplier.
3.2
HANDLING THE DELIVERY
The package must only be handled by means of a forklift truck or pallet mover. Slide the forks into the hole in the pallet and move the
mower to your selected location for its assembly or storage. Always transport only a single package.
The minimum load bearing capacity of the handling equipment is:
The wooden crate is not intended to be lifted by means of a crane.
Only persons with relevant authorisation and experience with the operation of the handling equipment may use it.
Due to the considerable weight of the packaged mower, we recommend at least two people for its handling.
3.3
STORAGE BEFORE UNPACKING
In the event that the mower will not be unpacked and assembled immediately upon deliver, store it under the following conditions:
-
Store the mower in its original packaging in a dry area protected against the effects of weather, which could result in the damage
of the packaging and deterioration of condition.
-
Do not tilt the wooden package on its side or, worse still, turn it upside down. Do not place any items on to the package from
which liquids could potentially leak.
-
Do not disassemble the mower from the pallet and do not turn it on its side and do not lean it in a diagonal position.
-
Do not place any other items or materials on to the packed mower.
-
When storing multiple packaged mowers then no more than four packages may be stacked on top of each other and a maximum
of two packages may be transported on top of each other.
Recommended storage location specifications:
Temperature
from -10 °C to +35 °C
Air humidity
<80 % at 21 °C
Air cleanliness
Dust-free environment
Other
Dry storage location
3.4
UNPACKING
► F irst remove the wooden boards using a suitable tool (crowbar, hammer, etc.), remove all the separately packaged assemblies
and then finally remove all the securing elements and packaging materials. Ensure that no part of the mower or its assemblies
are damaged.
► V isually inspect the mower and the separate assemblies for damage that may have occurred during transport. In the event of any
type of damage, immediately contact the supplier and do not continue with the assembly of the mower.
After unpacking everything, ensure that the packaging material is properly disposed of. The disposal must conform to relevant
waste disposal laws valid in your country. In the event that you are unsure about the disposal procedure, have this performed by
a specialised company.
SEPARATELY PACKAGED ASSEMBLIES
Unpack the following separately packaged assemblies:
-
Steering wheel
-
Seat
-
Seat arm rests
-
documentation(see the following chapter)
-
The grass catcher (is partially disassembled in a cardboard box, with hitches and joining material)
500 kg
75

Publicidad

loading

Este manual también es adecuado para:

Duke syc1222692052-002692053-00