Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH (
Original Instructions)
collar should be rotated until the desired setting is located
at the top of the tool. Locators are provided in the collar to
eliminate the guess work when selecting fastening torque.
The higher the number on the collar, the higher the torque
and the larger the fastener which can be driven. To lock
the clutch for drilling operations, move function collar (11)
to drill bit position.
Note: When using the drill/driver for drilling holes, be sure
that the torque adjusting collar is set so the figure of the drill is
aligned with the center line on the top ofthe tool. Failure to do
this will allow the clutch to slip while attempting to drill.
Dual range gearing (Fig. A and D)
The dual range feature of your driver/drill allows you to shift
gears for greater versatility.
To select the low speed, high torque setting, turn the tool
off and permit to stop. Slide the gear shifter (4) forward
(towards the chuck). To select the high speed, low torque
setting, turn the tool off and permit to stop. Slide the gear
shifter back (away from chuck).
Note: Do not change gears when the tool is running. If you
are having trouble changing gears, make sure that the dual
range gear shifter is either completely pushed forward
or completely pushed back.
Keyless single sleeve chuck (Fig. E)
Your tool features a keyless chuck with one rotating sleeve
for one-handed operation of the chuck. To insert a drill bit
or other accessory, follow these steps.
1. Lock the trigger in the OFF position as previously
described.
2. Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the sleeve
counterclockwise far enough to accept the desired
accessory.
3. Insert the accessory about 19mm (3/4") into the chuck
and tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with the
other. Your tool is equipped with an automatic spindle
lock mechanism. This allows you to open and close the
chuck with one hand.
4. To release the accessory, repeat step 2 above.
Warning! Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck and
personal injury may result. Always lock off trigger switch
when changing accessories. Be sure to tighten chuck with one
hand on the chuck sleeve and one hand holding the tool for
maximum tightness.
32
Chuck removal (Fig. F)
Turn the adjustment collar to the "drill" position and gear
shifter to position 1 (low speed). Tighten the chuck around
the shorter end of a hex key (not supplied) of 6.35mm (1/4")
or greater size. Using a wooden mallet or similar object,
strike the longer end in the clockwise direction, as shown.
This will loosen the screw inside the chuck.
Open chuck jaws fully, insert screwdriver (or Torx tool if
required) into front of chuck between jaws to engage screw
head. Remove screw by turning clockwise (left-hand-thread).
Place hex key in chuck and tighten, as shown in Fig. F.
Using a wooden mallet or similar object, strike key sharply
in the counterclockwise direction. This will loosen the chuck
so that it can be unscrewed by hand.
Chuck installation (Fig. G)
Screw the chuck on by hand as far as it will go and insert screw
(left-hand thread). Tighten screw securely. Tighten the chuck
around the shorter end of a 6.35mm (1/4") or larger hex key (not
supplied) strike the longer end in the clockwise direction with
a wooden mallet, as shown. Tighten the screw once again by
turning in a counterclockwise direction.
Drill Operation
Warning! To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power source
before making any adjustments or removing/installing
attachments or accessories.
Warning! To reduce the risk of personal injury, ALWAYS
ensure workpiece is anchored or clamped firmly. If drilling
thin material, use a wood "back-up" block to prevent
damage to the material.
Turn the collar to the drill bit symbol for drilling. Select the
desired speed/torque range using the gear shifter to match
the speed and torque to the planned operation.
1. Use sharp drill bits only. For WOOD, use twist drill bits,
spade bits, or hole saws. For METAL, use high-speed
steel (HHS) twist drill bits or hole saws.
2. Always apply pressure in a straight line with the bit. Use
enough pressure to keep drill biting, but do not push
hard enough to stall the motor or deflect the bit.
3. Hold tool firmly with both hands to control the twisting
action of the drill.
Warning! The drill may stall if overloaded causing a
sudden twist. Always expect the stall. Grip the drill firmly
with both hands to control the twisting action and avoid
injury.
4. IF DRILL STALLS, it is usually because it is being
overloaded or improperly used. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work, and determine
cause of stalling. DO NOT CLICK TRIGGER ON AND
Publicidad
