Publicidad
Idiomas disponibles
Idiomas disponibles
OFF IN AN ATTEMPT TO START A STALLED DRILL
— THIS CAN DAMAGE THE DRILL.
5. To minimize stalling or breaking through the material,
reduce pressure on drill and ease the bit through the
last fractional part of the hole.
6. Keep the motor running when pulling the bit back out of
a drilled hole. This will help prevent jamming.
7. With variable speed drills there is no need to center
punch the point to be drilled. Use a slow speed to start
the hole and accelerate by squeezing the trigger harder
when the hole is deep enough to drill without the bit
skipping out.
Hammerdrill operation (Fig. D)
1. Turn the collar (11) to the hammerdrill symbol.
2. Select the high speed setting by sliding the selector
forward (towards the chuck).
Important! Use carbidetipped or masonry bits only.
3. Drill with just enough force on the hammer to keep
it from bouncing excessively or "rising" off the bit.
Too much force will cause slower drilling speeds,
overheating and lower drilling rate.
4. Drill straight, keeping the bit at a right angle to the work.
Do not exert side pressure on the bit when drillling as
this will cause clogging of the bit flutes and a slower
drilling speed.
5. When drilling deep holes, if the hammer speed starts to
drop off, pull the bit partially out of the hole with tool stil
running to help clear debris from the hole.
Note: A smooth, even flow of dust from the hole indicates
proper drilling rate.
Operation as a screwdriver
Select the desired speed/torque range using the dual range
gear shifter on the top of tool to match the speed and torque
to the planned operation.
Insert the desired fastener accessory into the chuck as
you would any drill bit. Make a few practice runs in scrap or
unseen areas to determine the proper position of the clutch
collar.
MAXIMUM RECOMMENDED CAPACITIES
Low Range–1
Bits, Metal
6.00 mm
Drilling
Wood, Flat
19.00 mm
Boring
Hole Saws
19.00 mm
MAINTENANCE
Your STANLEY tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning. Your charger does not
require any maintenance apart from regular cleaning.
Warning! To reduce the risk of serious personal
injury, place the forward/reverse button in the lock-off
position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
f Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
f Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
f Regularly open the chuck and tap it to remove any dust
from the interior.
f The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Charger cleaning instructions
Warning! Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth or
soft non-metallic brush. Do not use water or any cleaning
High Range–2
solutions.
3.00 mm
RELIABILITY, repairs, maintenance and adjustment (other
12.00 mm
than those listed in thismanual) should be performed by
16.00 mm
authorized service centers or other qualified organizations,
always-using identicalreplacement parts. Unit contains no
user serviceable parts inside.
ENGLISH (
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Warning! Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust mask
when performing this procedure.
Warning! Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the materials
used in these parts. Use a cloth dampened only
with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool
into a liquid.
¡Important!To
ensure
Original Instructions)
product
SAFETY
and
33
Publicidad
