Miller XMT 350 CC/CV Manual Del Operador página 13

Keep flammables away from cutting. Do not cut near flammables.
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not cut on drums or any closed containers.
�
Hay una lista completa de piezas disponible en www.MillerWelds.com
Do not fuel a hot engine.
Do not fuel a hot engine.
Do not fuel a hot engine.
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not grip material near cutting path.
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift e
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift
Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
rating (see Specifications).
rating (see Specifications).
Do not weld on drums or any closed containers.
/
rating (see Specifications).
Turn off power before disassembling torch.
Writer: If necessary, replace the word "handle" with "lift eye'.
Do not use one handle to lift or support unit.
Do not weld on drums or any closed containers.
When power is applied failed parts can explode or cause other parts to explode.
Do not cut on drums or any closed containers.
When power is applied failed parts can explode or cause other parts to explode.
When power is applied failed parts can explode or cause other parts to explode.
Do not remove or paint over (cover) the label.
Do not spray water on electrical parts, including Engine Control Unit (ECU).
Drive rolls can injure fingers.
Do not cut on drums or any closed containers.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Do not grip material near cutting path.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Recycle or dispose of used coolant in an environmentally safe way.
Welding wire and drive parts are at welding voltage during operation
Always wear long sleeves and button your collar when servicing unit.
Turn off power before disassembling torch.
Do not grip material near cutting path. Always wear long sleeves and button your collar when servicing unit.
Always wear long sleeves and button your collar when servicing unit.
Hot Parts can burn. Do not touch hot parts bare-handed. Allow cooling period before handling parts or equip-
ment.
Consult rating label for input power requirements.
After taking proper precautions as shown, connect power to unit.
Turn off power before disassembling torch. After taking proper precautions as shown, connect power to unit.
Connect Green Or Green/Yellow grounding conductor to ground terminal first. After taking proper precautions as shown, connect power to unit.
Do not remove or paint over (cover) the label.
Connect input conductors (U/L1, V/L2, W/L3) to line terminals.
Writer: If necessary, replace the word "handle" with "lift eye'.
Become trained and read the instructions and labels before working on machine.
Disconnect input plug or power before working on machine.
Disconnect input plug or power before working on machine.
Do not remove or paint over (cover) the label.
Do not use one handle to lift or support unit.
Disconnect input plug or power before working on machine.
Environmental Protection Use Period (China)
Drive rolls can injure fingers.
Connect Green Or Green/Yellow grounding conductor to ground terminal first.
Connect input conductors (L1, L2, L3) to line terminals.
Wire
Welding wire and drive parts are at welding voltage during operation
Feed wire between guide pins into drive rolls.
Keep your head out of the fumes
Consult rating label for input power requirements.
Become trained and read the instructions and labels before working on machine.
Las chispas producidas por la soldadura pueden provocar incendios.
Tenga a mano un extinguidor y una persona que vigile lista para
usarlo.
<12.4 V
No suelde sobre tambores u otros recipientes cerrados.
+ +
No quite esta etiqueta ni la cubra con pintura.
Al salir despedidos, los pedazos de las piezas pueden causar lesio-
nes. Use siempre careta de protección cuando repare la máquina.
Siempre use mangas largas y el cuello abotonado cuando esté repa-
rando la unidad.
Conecte la alimentación de la máquina únicamente después de ha-
ber tomado las precauciones indicadas.
No use una sola manija para levantar o sostener la unidad.
Período de uso con protección medioambiental (China)
Wear hat and safety glasses. Use ear protection and button shirt
Use casco y lentes de seguridad. Use protección para los oídos y
collar. Use welding helmet with correct shade of filter. Wear complete
abotónese el cuello de la camisa. Use careta para soldar con un lente
body protection.
de protección adecuado. Use protección de cuerpo completo.
Wear hat and safety glasses. Use ear protection and button shirt
Become trained and read the instructions before working on the
Entrénese y lea las instrucciones antes de trabajar en la máquina o
collar. Use welding helmet with correct shade of filter. Wear complete
machine or welding.
soldar.
body protection.
Become trained and read the instructions before working on the
Become trained and read the instructions before working on the
machine or cutting.
machine or welding.
Become trained and read the instructions before working on the
machine or cutting.
Remove unit from shipping crate. Remove Owner's Manual from unit.
Read Owner's Manual for battery maintenance information.
keep hands and metal objects away.
Use lifting eye to lift unit and properly installed units only.
Use a proper cart to move unit.
keep hands and metal objects away.
OM-2254 Página 7
Safe
Safe1
Safe
Safe
Safe
Safe
Safe1
Safe1
Safe
Safe1
Safe
Safe
Safe
Safe
Safe11 Safe
Safe31 2017 04
Safe
Safe2
Safe2
Safe
Safe2
Safe2
Safe 11
Safe32 2012 05
Safe Safe
Safe2
Safe
Safe
Safe11
Safe33 2017 04
Safe2
Safe2
Safe
Safe
Safe2
Safe120
Safe34 2012 05
Safe
Safe
Safe2
Safe2
Safe
Safe12
Safe
Safe
Safe2
Safe
Safe
Safe12
Safe35 2012 05
Safe
Safe12
Safe36 2012 05
Safe
Safe12
Safe38 2012 05
Safe7 2017 04
Safe39 2012 05
Safe40 2012 05
Safe
Safe41 2012 05
Safe40 2012 05
Safe