Publicidad
Idiomas disponibles
Idiomas disponibles
SUB OUT JACKS
Q) SUB IN JACKS
These are output jacks for output of processed signals.
These are the input jacks of the built-in main amplifier.
SPEAKER SYSTEM
These are terminals for connection of one pair of |joudspeakers.
@
AC
POWER
CONNECTION
The
correct pwer for operation your system is written on the
rear
panel.
Be
sure
the POWER
push-switch
is out
before
plugging the AC line cord into an electrical outlet.
FRONT PANEL
FEATURES
(2
q
POWER
SWITCH
Press once
to turn power ON, then once again to turn power
OFF.
VOLUME
CONTROL
This control is used only for adjusting the level of the proces-
sed signals from the SUB OUT jacks.
REVERBERATION
CONTROL
Use
this knob
to control
the reverberation
time (DELAY).
When
turned
toward
the MAX
side, the delay is increased;
when turned toward the MIN side, the delay is decreased.
EFFECTOR
SWITCHES
MATRIX:
Press to apply the matrix signal to the signal output from the
SUB OUTPUT terminals.
When
this
switch
is pressed,
the
indicator
lights and
the
MATRIX function is activated.
In music source, a good deal of indirect sound (reflected wave
component)
is included
other than the direct sound
signals.
When
this MATRIX
function
is activated, direct wave com-
ponents
(in-phase
components)
are
decreased
and a
lively
sound can be reproduced, full of on-the-scene feeling.
DELAY:
Press to apply the delay signal output from the SUB OUTPUT
terminals.
When listening to live music such as in a concert
hall, indirect
sound reflected off the walls or ceiling of the hall is also heard
other than the direct sound
from the instruments
played by
the musicians.
In this way, the actual music signal consists of the direct sound
'components
that come
directly into the ears and the indirect
'sound components such as reflections or reverberations.
The
DELAY
circuit produced these reverberations electrically.
When the DELAY
circuit is activated, the depth of the sound
can
be reproduced
with the on-the-spot
feeling of theater or
concert hall.
TIME DIF:
Press to differentiate the delay time between the left and the
right channels.
When
this
switch
is pressed,
the
indicator
tights
and
the
difference
of delay
times
between
left and
right channels
can beset with the DELAY TIME UP/DOWN switch.
DELAY TIME MEMORY SWITCHES
When
the MEMO
switch
is pressed,
the
indicator
lights for
approx.
5 seconds
so that
the delay
time
can be stored
in
memory.
During this time, pressing the M1, M2 or M3 switch
(the corresponding
indicator
lights) stores to displayed delay
time in memory.
After the delay time settings have been memorized, press the
M1 (M2 or M3) switch to obtain the preset delay time.
DELAY
TIME
UP/DOWN
SWITCH:
Press to adjust the delay time. Pressing the UP section of
this switch extends the delay time (00 to 99 msec}.
Pressing the DOWN
section shortens the delay time (99 to 00
msec).
When
this switch
is kept pressed
for more
than 0.5 seconds,
the delay time is varied continuously.
ADJUSTING
THE
DELAY
TIME
DIFFERENCE
BETWEEN
LEFT
AND
RIGHT
CHANNELS:
For improving the effect of DELAY
circuit, the delay time of
right channel
is set at 5 msec. later than the delay time of left
channel
in this unit. Since the DELAY
TIME display shows
only the left channe} delay time, the right channel delay time
is 5 msec, less than the displayed value.
To change the difference of delay time between
the left and
right
channels,
keep
pressing
the
UP/DOWN
switch
while
pressing the TIME
DIFF switch described in section (15), The
DELAY
TIME
display
is changed
to delay difference display
so that
the
difference
of the
right channel
from
the teft
channel
can
be set within a margin of +15 msee. When
the
UP/DOWN
switch
is released, the display will be changed to
DELAY
TIME
indications
again, approx.
1.5 seconds
later.
The
delay
differentiation
set as above can also be stored
in
memory together with the delay time.
For example:
When
memorizing
a 40 msec
Delay Time with a Delay dif-
ference value of —10 into switch M1.
(1)
Press the DELAY
TIME
UP/DOWN switch and adjust the
value to 40,
(2)
Press the
UP/DOWN
switch
while
pressing
the TIME
DIFF switch and set the value to —10.
(3)
Press the MEMO
button. Then, after the indicator lights,
press the M1 button.
Now, memorizing is completed.
GRAPHIC
EQUALIZER
Use these controls
to change
the quality
of the SUB OUT
signals.
NOTE:
This graphic equalizer only affects the SUB OUT signals.
SOURCE
SELECTOR
Use this switch to select the program source.
.
The indicator for the source which has been selected will light.
Only the video
signals of the VCR, TV/DBS, and
LV sources
can be selected.
LINE is only for output of audio signals.
REC
OUT
SELECTOR
Use this switch
for recording or dubbing onto th: tape deck.
Any
of the components
connected
to the jackson
the rear
panel can be selected (TAPE 1, TAPE 2, SOURCE,
Hifi VCR},
regardiess of the SOURCE SELECTOR.
Recording
of
the
signals
choosen
using
the
SOURCE
SELECTOR
is possible in the SOURCE
position.
Publicidad
