Publicidad
Idiomas disponibles
Idiomas disponibles
BD600ND
BD600ND
00010
A
5.3) Alarms/Warnings:
BD600ND
00010
these appear during operation on the right-hand side of the screen and inform the operator about
00010
the status of the tool.
BD600ND
BD600ND
menti
B
Message
00010
00010
BD600ND
BD600ND
BD600ND
00010
BD600ND
00010
C
S/N 24AW125
00010
FW
S1J76100
BD600ND
BD600ND
BD600ND
30000
BD600ND
00010
00010
00010
00010
BD600ND
BD600ND
BD600ND
BD600ND
00010
00010
30001
00010
BD600ND
BD600ND
menti
BD600ND
5.4) Errors:
00010
00010
appear during operation on the right-hand side of the screen and are accompanied by an acoustic
00010
BD600ND
BD600ND
signal and blinking LEDs, informing the operator of any procedural or operating errors.
BD600ND
menti
00010
00010
Message
00010
BD600ND
BD600ND
menti
BD600ND
BD600ND
BD600ND
BD600ND
BD600ND
00010
00010
00010
00010
00010
00010
BD600ND
BD600ND
00010
BD600ND
BD600ND
BD600ND
BD600ND
BD600ND
00010
30001
00010
00010
00010
00010
BD600ND
00010
BD600ND
BD600ND
BD600ND
BD600ND
BD600ND
00010
00010
30001
00010
00010
BD600ND
00010
BD600ND
BD600ND
BD600ND
BD600ND
30001
00010
00010
00010
00010
BD600ND
BD600ND
BD600ND
menti
BD600ND
menti
menti
menti
00010
00010
00010
00010
BD600ND
BD600ND
BD600ND
BD600ND
00010
00010
00010
00010
BD600ND
BD600ND
BD600ND
BD600ND
Error messages remain on the display for a few seconds after which the error resets. They
00010
00010
00010
00010
reappear in the event of a permanent fault.
BD600ND
BD600ND
BD600ND
BD600ND
30001
30001
30001
30001
!
001
!
Lorem ipsum
002
!
Meaning
003
BATTERY
!
DISCHARGED
004
!
BATTERY HIGH
TEMPERATURE
001
!
MAINTENANCE
002
!
REQUIRED
001
!
!
!
003
001
002
!
!
!
004
002
003
Description of the error
durante il funzionamento
!
Operate the release button before
!
the target force/pressure is reached.
003
004
!
Interruption of signal from the bat-
OK
tery NTC temperature probe.
004
Abnormal motor current consump-
OK
!
!
tion.
!
!
The tool stops.
001
001
001
001
Pressure transmitter output voltage
!
!
!
not within specified range.
!
002
002
002
002
Failure to reach calibration pressure
!
!
!
!
within 30 sec. of continuous tool
003
003
operation.
003
003
!
Battery overload with protection
!
!
!
intervention.
004
004
004
The tool stops.
004
Replace or recharge the battery.
NOTE: To preserve the battery, the tool will not start when battery
voltage falls below a minimum safe threshold. However, it is still
possible to finish the current work cycle.
Remove the battery and wait for it to cool down.
To cool it down more quickly, the battery can be inserted into the
supplied charger using the specific 'AIR COOLED' function.
The number of cycles required for routine maintenance has been
reached; the tool continues to operate but it is advisable to send it to
CEMBRE for a complete overhaul (section 7).
This screen will always reappear after 30 s of inactivity of the tool.
Solution
Repeat the work cycle and wait for the motor to stop
automatically. If the ram is not fully retracted, restart and
complete the compression action.
Replace the battery.
If the problem persists, contact CEMBRE.
Wait for the LEDs to go out (180 sec.), or remove and
reinsert the battery, then restart the tool.
If the error occurs frequently, contact CEMBRE.
Repeat the work cycle. If the error occurs frequently,
contact CEMBRE.
Repeat the work cycle. If the error occurs frequently,
contact CEMBRE.
Wait for the LEDs to go out (180 sec.), or remove and
reinsert the battery, then restart the tool.
If the error occurs frequently, contact CEMBRE.
Description
Errori/avvertiment
14
Publicidad
