Sony TCM-AP5V Manual De Instrucciones página 2

English
Welcome!
Thank you for purchasing the Sony Cassette-Corder.
Some features are:
• DPC (Digital Pitch Control) allows you to adjust the speed and
pitch of the playback sound.
• You can increase or decrease the playback tape speed within
the range of approximately +100% to –50%. If you change the
playback tape speed, the pitch will be automatically adjusted.
• Built-in flat microphone for clear recording of speaker's voice.
•The BATT/REC lamps indicate the remaining battery power in
two steps and the i lamp indicates when to replace the
batteries.
• VOR (Voice Operated Recording) system that starts and stops
recording automatically in response to the sound, to save tapes
and batteries.
• Automatic shut-off mechanism at the end of the tape (in the
recording/playback mode only).
• Stop-pause-release function—The pause switch is released
automatically when the p button is depressed, so that you
don't miss a recording chance.
z Getting Started
Preparing a Power Source
Choose one of the following power sources.
Dry Batteries (see Fig. A-a)
Make sure that nothing is connected to the DC IN 3V jack.
1 Open the battery compartment lid.
2 Insert two R6 (size AA) batteries (not supplied) with correct
polarity and close the lid.
To take out the batteries (see Fig. A-b)
To attach the battery compartment lid if it is
accidentally detached (see Fig. A-c)
Attach as illustrated.
Battery life (Approximate hours)
Recording
Sony alkaline LR6 (SG) 8.5
Sony R6P(SR) 2
We recommend to use long-life alkaline batteries.
Notes
• Do not charge a dry battery.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
• When you do not use the unit for a long time, remove the batteries to avoid
any damage caused by battery leakage and subsequent corrosion.
• Dry batteries will not be expended when another power source is connected.
When to replace the batteries (see Fig. A-d)
Replace the batteries with new ones when the BATT/REC lamps
go off and the i lamp flashes.
The BATT/REC lamps change as illustrated.
Notes
• During FF(CUE) or REW(REVIEW), the i lamp may flash. Only when the
tape does not run properly, replace the batteries.
• In some cases when the unit is used with rechargeable batteries, only one
BATT/REC lamp will light even though the batteries have been fully
charged.
• After the batteries have been used for a while, the BATT/REC lamp(s) may
flash with the playback sound when you turn up the volume; however, this
does not mean that you need to replace the batteries.
• The unit will play back normally for a while even after the i lamp flashes.
However, replace the batteries as soon as you can. If you do not, a loud noise
may be emitted by the built-in speaker or subsequent recording will not be
done correctly.
• When the tape starts running or at the end of the tape the i lamp may
momentarily light. If the lamp goes off, you do not need to replace the
batteries.
House Current (see Fig. A-e)
Connect the AC power adaptor to DC IN 3V and to the wall
outlet. Use the AC-E30HG AC power adaptor (not supplied).
Do not use any other AC power adaptor.
Polarity of the plug
z Operating the Unit
Recording (see Fig. B-a, b)
You can record the sound easily with the built-in microphone.
Use a normal (TYPE I) tape.
Make sure that nothing is connected to the MIC jack.
1 Open the cassette compartment lid.
2 Take out any slack in the tape and insert the cassette with
the side to start recording facing the lid.
3 Close the cassette compartment lid.
4
Set VOR to L , H or OFF. For details, see "VOR (Voice
Operated Recording)".
5 Press r REC.
Recording starts.
Place the unit on a hard surface such as a desk with the
cassette holder side up so that the flat mic can record
effectively.
While the tape runs, the REC lamp lights and flashes
depending on the strength of the sound.
At the end of the tape, recording stops and the unit turns off
automatically.
To Press or slide
p STOP
Stop recording
Pause recording PAUSE c
To release pause recording, release PAUSE c*.
Take out a cassette Press p STOP and open the cassette compartment
lid by hand.
* PAUSE c will be also automatically released when p STOP is pressed
(stop-pause-release function).
Note
Do not use a CrO (TYPE II) or metal (TYPE IV) tape, otherwise the sound may
2
be distorted when you play back the tape, or the previous recording may not be
erased completely.
To prevent a tape from being accidentally recorded
over (see Fig. B-c)
Break out and remove the cassette tabs. To reuse the tape for
recording, cover the tab hole with adhesive tape.
Playing a Tape (see Fig. C)
1 Open the cassette compartment lid.
2 Insert a cassette with the side to start playing facing the lid.
3 Close the cassette compartment lid.
4 Press ( PLAY then adjust the volume.
At the end of the tape, playback stops and the unit turns off
automatically.
To
Stop playback
Pause playback
Fast forward**
Rewind**
Search forward
during playback (CUE)
Search backward
during playback (REVIEW)
Take out a cassette
* PAUSE c will be also automatically released when p STOP is pressed
(stop-pause-release function).
** If you leave the unit after the tape has been wound or rewound, the batteries
will be consumed rapidly. Be sure to depress p STOP.
Using Various Functions (see Fig.
D)
Using tape counter
Before recording, press the counter reset button to set the TAPE
COUNTER to 000. It is useful to search the beginning of the
recording.
VOR (Voice Operated Recording)
Set VOR to L or H. Press r REC, and the unit automatically
starts recording the sound and pauses when there is no sound
(you can save tapes and batteries). You can set VOR to L or H
Playback
during recording too.
8.5
H : To record at meetings or in a quiet place.
2 L : To record for dictation in a noisy place.
When you use this system in a noisy place the unit stays in the
recording mode. If the sound is too soft, on the contrary, the unit
will not start recording. Set VOR to L (low) or H (high)
depending on the conditions. When you do not use this
function, set VOR to OFF.
Notes
• The VOR system depends on the environment conditions. If you cannot get
the desired results, set VOR to OFF.
• When using the VOR system, the unit starts recording only when a sound is
detected, therefore, the beginning of the word may not be recorded. For an
important recording, we recommend setting VOR to OFF.
To monitor the sound
Connect an earphone (not supplied) firmly to the EAR jack. The
sound for monitoring cannot be adjusted by VOL. The recording
level is fixed.
Start recording during playback
Press r REC during playback, recording starts immediately. It is
useful when you want to re-record the portion which was just
recorded.
Review the portion just recorded
Press 0 REW/REVIEW during recording. Release the button
at the point to start playback.
When the tape comes to an end (automatic
shut-off mechanism)
Recording or playback stops and the unit turns off
automatically.
DPC (Digital Pitch Control) and
Speed Control Function
How to adjust the pitch combined with the tape
playback speed
Adjust SPEED/PITCH CONTROL as follows:
To play back
slower
at normal speed
faster
Notes
• Even though you use the DPC switch, you cannot acquire the same pitch as
the original. The tone will be somewhat different from the original.
• When the power of the batteries becomes weak, SPEED/PITCH CONTROL
may make noise if you turn it fast. In that case turn it slowly or change the
batteries.
• When SPEED/PITCH CONTROL is turned or the volume is adjusted during
playback, BATT/REC lamps may flicker.
Recording from Various Sound
Sources
Notes (Before recording)
• When connecting cords, be sure you connect plugs firmly.
• Make a trial recording to make sure that you made connections correctly and
adjusted the volume properly.
• The following examples use Sony products. If you have any problem when
using other products, read the instruction manual of those products.
Recording with an External Microphone
(see Fig. E-a)
Connect a microphone to the MIC jack.
The built-in microphone will be disconnected and the sound
through the external microphone will be recorded.
When using a plug-in-power system microphone, the power to
the microphone is supplied from this unit.
To start recording, insert a cassette and press r REC.
Note
When recording with an external microphone, the VOR system may not work
properly because of the difference in sensitivity.
Recording from Another Equipment
(see Fig. E-b)
Connect another equipment to the MIC jack using the RK-
G64HG connecting cord (not supplied).
1 Insert a cassette.
2 Adjust the sound of the connected equipment.
3 Press r REC.
Press or slide
p STOP
PAUSE c
To release pause playback, release
PAUSE c*.
) FF/CUE during stop
0 REW/REVIEW during stop
Press and hold ) FF/CUE and
release it at the point you want
Press and hold 0 REW/REVIEW
and release it at the point you want
Press p STOP and open the cassette
compartment lid by hand.
Set SPEED/PITCH CONTROL to
SLOW
Center
FAST
z Additional Information
Precautions
On power
Operate the unit only on 3V DC. For AC operation, use the AC
power adaptor recommended for the unit. Do not use any other
type. For battery operation, use two R6 (size AA) batteries.
On the unit
• Do not leave the unit in a location near heat sources, or in a
place subject to direct sunlight, excessive dust or mechanical
shock.
• Should any solid object or liquid fall into the unit, remove the
batteries or disconnect the AC power adaptor, and have the
unit checked by qualified personnel before operating it any
further.
• If the unit has not been used for a long time, set it in the
playback mode and warm it up for a few minutes before
inserting a tape.
Keep personal credit cards using magnetic coding or spring-
wound watches etc. away from the unit to prevent possible
damage from the magnet used for the speaker.
On tapes longer than 90 minutes
We do not recommend the use of tapes longer than 90 minutes
except for a long continuous recording or playback. They are
very thin and tend to be stretched easily.
If you have any questions or problems concerning your unit,
please consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks,
consult your nearest Sony dealer.
Recording cannot be made.
m No cassette is inserted.
m The tab on the tape has been removed. To reuse the tape for
recording, cover the tab hole with adhesive tape.
m The batteries are weak. Replace both batteries with new ones.
m The record/playback head is contaminated.
Playback cannot be made.
m The tape has reached the end. Rewind the tape.
m The record/playback head is contaminated.
During CUE/REVIEW the tape stops or does not run.
You cannot fast-forward or rewind.
m The batteries are weak. Replace both batteries with new ones.
The unit does not operate.
m The batteries have been inserted with incorrect polarity.
m The batteries are weak. Replace both batteries with new ones.
m PAUSE c is slid in the direction of the arrow.
m The AC power adaptor or car battery cord is not firmly connected.
m The batteries have been inserted, but simultaneously the AC
power adaptor is connected and not to be done to the wall outlet.
No sound comes from the speaker.
m The earphone is plugged in.
m The volume is turned down completely.
The sound drops out, sound quality becomes worse or
sound has excessive noise.
m The batteries are weak. Replace both batteries with new ones.
m The record/playback head is contaminated.
m If the cassette has been put on a speaker without its case, the
sound quality may be distorted.
m CrO (TYPE II) or metal (TYPE IV) tape is used.
2
Recording is interrupted.
m VOR is set to L or H. When you do not use VOR, set it to OFF.
The sound is not stable and becomes out of pitch
suddenly.
m SPEED/PITCH CONTROL is set at a point other than the center.
m The batteries are weak. Replace both batteries with new ones.
m The capstan and pinch-rollers are contaminated.
Recording cannot be erased completely.
m The erase head is contaminated.
Tape speed is too fast or too slow in the playback
mode.
m SPEED/PITCH CONTROL is set at a point other than the center.
While operating, some noise is heard.
m The counter reset button is pressed incorrectly. Press it correctly to
set to 000.
When the tape has reached the end after fast forward
or rewind, noise is heard.
m The unit is not in stop mode. Press p STOP.
Maintenance (see Fig. F)
To clean the tape heads and path
Depress r REC while pushing the lever.
Wipe the heads, pinch rollers, and the capstans with a cotton
swab moistened with alcohol every 10 hours of use.
To clean the exterior
Use a soft cloth slightly moistened in water. Do not use alcohol,
benzine or thinner.
Specifications
Recording system
2-track 1 channel monaural
Frequency range
250 – 6,300 Hz
Speaker
7
Approx. 3.6 cm (1 / in.) dia.
16
Power output
150 mW (at 10 % harmonic distortion)
Input
Microphone input jack (minijack) sensitivity 0.2 mV for
3 kilohms or lower impedance microphone
Output
Earphone jack (minijack) for 10 kilohms or lower impedance earphone
Variable range of the tape speed
from +100% to –50%
Power requirements
3V DC
Two R6 (size AA) batteries
Dimensions (w/h/d) (incl. projecting parts and controls)
Approx. 90.9 × 113.0 × 37.8 mm
× 4 × 1
(3 5 / 1 / 1 / in.)
8 2 2
Mass
Approx. 205 g (7.3 oz.) not incl. batteries
Approx. 275 g (9.8 oz.) incl. batteries, cassette
Design and specifications are subject to change without notice.