About Remaining Battery Indicator; Prior To Operation - Hitachi Koki CG 36DL Instrucciones De Manejo

ABOUT REMAINING BATTERY INDICATOR

When pressing the remaining battery indicator switch, the
remaining battery indicator lamp lights and the battery
remaining power can be checked. (Fig. 5) When releasing
your fi nger from the remaining battery indicator switch, the
remaining battery indicator lamp goes off . The Table 5
shows the state of remaining battery indicator lamp and the
battery remaining power.
State of lamp
The battery remaining power is enough.
The battery remaining power is a half.
The battery remaining power is nearly
empty.
Re-charge the battery soonest possible.
As the remaining battery indicator shows somewhat
diff erently depending on ambient temperature and battery
characteristics, read it as a reference.
NOTE
◯ Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
◯ To save the battery power consumption, the remaining
battery indicator lamp lights while pressing the remaining
battery indicator switch.
◯ When using a back pack power supply (BL36200),
please check the battery level on the battery level display
of the back pack power battery.
For details, please see the BL36200 instruction manual.

PRIOR TO OPERATION

CAUTION
Pull out battery before doing any assembly.
1. Installing the loop handle (Fig. 6) (CG36DL (L),
CG36DAL (L) only)
(1) Remove the M6 × 43 bolts (2 pcs.).
(2) Install the loop handle on the main pipe so that it leans
against the housing.
(3) Place the handle fi xture at the lower end of the main pipe
and secure it fi rmly using M6 × 43 bolts (2 pcs.) and M6
nuts (2 pcs.).
NOTE
Secure the loop handle in a location that provides a good
grip.
CAUTION
Install the loop handle properly and securely as instructed
in the handling instructions.
If not attached properly or securely, it may come off and
cause injury.
2. Installing the bicycle-style handlebars (Fig. 7)
(1) Using the 4 mm hex wrench that is included, remove
the four bolts that have been temporarily secured to the
handle brace (A).
(2) Attach the right-hand side handgrip that has the lever and
the left-hand side handgrip, and then carefully secure the
handle brace (A) using the four bolts.
NOTE
Secure the left and right handgrips in a position that
provides a good grip.
Table 5
Battery Remaining Power
CAUTION
Install the left and right handgrips properly and securely
as instructed in the handling instructions.
If not attached properly or securely, it may come off and
cause injury.
3. Extending the main pipe (Fig. 8)
(1) Release the locking lever to allow the main pipe to be
extended.
(2) Extend the main pipe as far as it will go, making sure that
you hear it click.
NOTE
The motor will not operate unless the main pipe is fully
extended.
When you push the power button, the red power light will
fl ash rapidly.
(3) After extending the main pipe until it clicks, check that
the hole of the holder case is aligned with the hole of the
main pipe and lock the locking lever to fi x the main pipe
securely.
4. Installing cover (See Fig. 9 and 10)
WARNING
Be sure to install the cover in its designated location.
Failure to heed this warning may result in injury from
fl ying stones.
NOTE
Use the supplied hex. bar wrench 4 mm for installation.
(1) Use the supplied D5 tapping screw to install the knife in
the cover. (Fig. 9)
(2) Align the two holes in the cover bracket and the cover
and insert two M6 × 25 hex. socket button bolts. (The
cover bracket is installed in the motor case.)
(3) Place the cover holder on the underside of the cover and
use the supplied hex. bar wrench 4 mm to alternately
tighten the two M6 × 25 hex. socket button bolts until they
are properly tightened.
CAUTION
◯ Take care to avoid cutting yourself on the knife inside the
cover.
◯ Install the cover and knife properly and securely as
instructed in the handling instructions.
If not attached properly or securely, they may come off
and cause injury.
5. Installing the cutting blade (optional accessory)
(CG36DL only)
WARNING
◯ Before installing the cutting blade, be sure to attach
the blade cover, wear thick gloves and take any other
necessary precautions to protect yourself.
◯ Before installing the cutting blade, check carefully and
make sure that it is not cracked, deformed or in any other
way damaged.
◯ When installing the cutting blade, fi rst attach the cutting
blade cover, securing the hole in the middle of the cutting
blade to the fl ange assy projection so that the cutting
blade fi ts into the nut cover and the center part of the
cutting blade does not slip. (See Fig. 20)
◯ After installing the cutting blade, don't forget to remove
the hex wrench and box spanner.
◯ If the left side M10 installation nut or the nut cover shows
signs of wear or abrasion, replace with a new installation
nut or nut cover.
(1) Insert the fl ange assy into the motor case. At this time,
the wing of the fl ange assy should face the motor case
side. (Fig. 17)
(2) To install the cutting blade, insert the supplied hex. bar
wrench into the holes in the fl ange assy and the motor
case, and, in order, attach the cutting blade and nut
cover. (Fig. 18)
Install the cutting blade by rotating in the direction
indicated by the arrow.
English
19