Descargar Imprimir esta página

Stanley SCH10 Manual Del Usuario página 35

Publicidad

Idiomas disponibles

Idiomas disponibles

button locks the tool in the off position. When changing the
position of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Worklight (Fig. A)
There is a worklight (8) located under the torque adjustment
collar (3). The worklight will be activated when the trigger
switch is squeezed.
NOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Fuel Gauge (Fig. A)
The tool includes a fuel gauge. When the trigger switch is
pressed, the LED lights will indicate the approximate level of
charge remaining.
Torque Adjustment Collar (Fig. A)
Turn (11) to screw symbol. The torque adjustment collar (3) is
clearly marked with numbers and a drill bit symbol.The collar
should be rotated until the desired setting is located at the
top of the tool. Locators are provided in the collar to eliminate
the guess work when selecting fastening torque. The higher
the number on the collar, the higher the torque and the larger
the fastener which can be driven. To lock the clutch for drilling
operations, move function collar(11) to drill bit position.
NOTE: When using the Impact drill/driver for drilling holes, be
sure that the function collar is set so the figure of the drill is
aligned with the center line on the top of the tool. Failure to do
this will allow the clutch to slip while attempting to drill.
Dual Range Gearing (Fig. A, D)
The dual range feature of your driver/drill allows you to shift
gears for greater versatility.
To select the low speed, high torque setting, turn the tool off
and permit to stop. Slide the gear shifter (4) forward (towards
the chuck). To select the high speed, low torque setting, turn
the tool off and permit to stop. Slide the gear shifter back
(away from chuck).
NOTE: Do not change gears when the tool is running. If you
are having trouble changing gears, make sure that the dual
range gear shifter is either completely pushed forward or
completely pushed back.
Keyless Single Sleeve Chuck (Fig. E)
Your tool features a keyless chuck with one rotating sleeve for
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Lock the trigger in the OFF position as previously
described.
ENGLISH (
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 19 mm (3/4") into the chuck
and tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with the
other. Your tool is equipped with an automatic spindle
lock mechanism. This allows you to open and close the
chuck with one hand.
To release the accessory, repeat step 2 above.
WARNING: Do not attempt to tighten drill
bits (or any other accessory) by gripping the
front part of the chuck and turning the tool
on. Damage to the chuck and personal injury
may result. Always lock off trigger switch when
changing acces sories.
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
CHUCK REMOVAL (Fig. F)
Turn the adjustment collar to the "drill" position and gear
shifter to position 1 (low speed). Tighten the chuck around
the shorter end of a hex key (not supplied) of 6.35 mm (1/4")
or greater size. Using a wooden mallet or similar object,
strike the longer end in the clockwise direction, as shown.
This will loosen the screw inside the chuck.
Open chuck jaws fully, insert screwdriver (or Torx tool if
required) into front of chuck between jaws to engage screw
head. Remove screw by turning clockwise (left-hand-thread).
Place hex key in chuck and tighten, as shown in Fig F. Using
a wooden mallet or similar object, strike key sharply in the
counterclockwise direction. This will loosen the chuck so that
it can be unscrewed by hand.
CHUCK INSTALLATION (Fig. G)
Screw the chuck on by hand as far as it will go and insert
screw (left-hand thread). Tighten screw securely. Tighten the
chuck around the shorter end of a 6.35 mm (1/4") or larger
hex key (not supplied) strike the longer end in the clockwise
direction with a wooden mallet, as shown. Tighten the screw
once again by turning in a counterclockwise direction.
Drill Operation
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect
tool from power source before making
any adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of personal
injury, ALWAYS ensure workpiece is
Original Instructions)
35

Publicidad

loading