EINHELL GE-WS 18/150 Li Manual De Instrucciones página 15

2. Pour the amount of liquid (e.g. water)
specifi ed by the solution manufacturer into
the spray container. If the spray solution has
not been prepared ready for spraying, add the
measured quantity of concentrated additive
and close the container carefully.
3. If you have not already done so, mix the
concentrated additive with the water (or other
liquid) by shaking the chemical sprayer.
4. Apply the name of the spray solution you
are using to the spray solution tank (e.g. by
means of a sticker).
5.4 Installing the battery (Fig. 8)
Note:
•
The equipment is supplied without a battery
and without a charger.
•
The cover flap closes by itself and is held in
position by magnets.
Open and hold the cover fl ap (15). Push the
battery into the battery mount provided. Make
sure that the pushlock button (22) engages as
soon as the battery has been pushed in all the
way. To remove the battery, proceed in the reverse
order.
5.5 Using the harness (Fig. 9)
Slip the harness over your shoulders and adjust
the length of the harness so that you can work
without fatigue. To do so, pull on the two ends
of the harness to shorten it (18) or on the two
harness release mechanisms to extend it (19).
Note: Should the fastening hooks for the harness
(20) come off , attach them back in position again
as shown in Figs. 4-5.
6. Operation
WARNING!
Check the equipment for damage before you use
it. Never use the equipment if it is damaged.
•
Check the tank for damage each time before
and after using the equipment.
•
Check the hose and all screw connections for
damage and leaks each time before and after
using the equipment.
6.1 Switching on (Fig. 10)
After inserting the battery, switch the equipment
on by turning the On/Off switch to the "I" position
(16).
Anl_GE_WS_18_150_Li_USA_SPK7.indb 15 Anl_GE_WS_18_150_Li_USA_SPK7.indb 15
EN
6.2 Switching off (Fig. 10)
Switch the equipment off by turning the On/Off
switch to the "0" position (16).
6.3 Spraying
WARNING!
Note the attached leafl et with the safety
instructions.
•
Do not use a very wide jet when spraying
plants or other objects directly.
•
When the trigger lever on the spray gun
handle is pressed, recoil forces can occur
suddenly, in the worst case scenario causing
the spray tube to point towards the body.
Always keep tight hold of the spray gun
handle.
•
Perform spraying only when the tank is
vertical or upright.
6.3.1 Switching spraying on/off
•
To spray, press the trigger lever on the spray
gun handle (Fig. 11).
•
The spray jet will stop when you let go of the
trigger lever.
•
If the trigger lever is pressed and then pushed
forward (Fig. 12), this locks the lever. The
equipment continues spraying until the trigger
lever is pulled back again and released.
Notes!
1. If the integrated pump contains too little
spray solution or none at all, it will run after
the chemical sprayer is switched on. Press
the trigger lever on the spray gun handle for
several seconds. The pump will fi ll up and
spray solution will be ejected irregularly. Once
the spray solution is ejected evenly, the pump
will switch off upon releasing the trigger lever
and will switch on again upon pressing the
lever.
2. If there is too little spray solution in the spray
solution container, the pump will suck in too
little spray solution (see section 1) and will
continue to run upon releasing the trigger
lever. Top up with spray solution (see section
5.3).
3. The suction hose is inside the tank on the
right-hand side. To empty the tank as far
as possible during spraying, bend slightly
forwards and a little to the right.
- 15 -
25.07.2023 14:54:35 25.07.2023 14:54:35