EINHELL GE-WS 18/150 Li Manual De Instrucciones página 17

the liquid properly for subsequent use or dispose
of it in accordance with the applicable regulations.
1. Unscrew the tank lid (8) from the tank.
2. Remove the fi lling strainer (10) and clean it
with ample water as required.
3. Tilt the tank forward and empty it completely.
4. Reinsert the fi lling strainer (10) in the tank
opening. Make sure that the seal (11) is
correctly seated.
5. Screw the tank lid (8) back on the tank.
6. Shake the chemical sprayer vigorously
several times.
7. Spray the contents onto the area just treated
or an area reserved for this purpose.
8. Repeat this process.
9. The container can now be drained through
the fi ller opening as described above.
10. Allow the tank to dry out completely.
Before you use the tank again, re-insert the fi lling
strainer and screw the tank lid back onto the tank.
7.3 Cleaning the intake fi lter (Fig. 15)
Clean the intake fi lter in the tank at least once
a year, ideally after the winter break or when
there are problems (see section 10). Proceed as
follows:
1. Empty the tank as described in 7.2.
2. Pull the suction hose (12) with intake fi lter off
the pump connection (13).
3. Rinse the suction hose and clean the intake
fi lter (14) with a brush in clear water.
4. Refi t the suction hose (12) to the pump
connection (13) and make sure that the intake
fi lter extends to the bottom of the tank. Only
then can the tank be properly emptied during
spraying.
7.4 Cleaning the fi lter element in the handle
(Fig. 16-17)
Clean the fi lter element in the handle at least
once a year, ideally after the winter break or when
there are problems (see section 10). Proceed as
follows:
1. Unscrew the union nut (5) from the handle (4).
2. Pull the fi lter (6) out of the handle (4) and
clean it with a brush in clear water.
3. Re-insert the fi lter (6).
4. Screw the union nut (5) securely back onto
the handle (4).
Anl_GE_WS_18_150_Li_USA_SPK7.indb 17 Anl_GE_WS_18_150_Li_USA_SPK7.indb 17
EN
7.5 Cleaning the nozzle and the adjustable
spray head
Clean the nozzle and the adjustable spray head
at least once a year, ideally after the winter break
or when there are problems (see section 10).
Never blow out the nozzle or the spray head
directly using your mouth. Proceed as follows:
1. Turn the adjustable spray head
counterclockwise as far as it will go (Fig. 18).
2. Clean the exposed nozzle (Fig. 19) and the
hole in the spray head (Fig. 20) of residue
using a thin wire.
3. Flush the nozzle and spray head with clear
water.
4. Allow the nozzle and spray head to dry.
7.6 Maintenance
There are no other parts inside the equipment
which require maintenance.
8. Disposal and recycling
The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
9. Storage and transport
9.1 Storage
Store the equipment and its accessories out
of children's reach in a dark and dry place at
above freezing temperature. The ideal storage
temperature is between 41°F and 86°F
(5°C and 30°C). Keep the electric tool in its
original packaging.
Equipment must always be stored completely dry
and clean.
- 17 -
25.07.2023 14:54:35 25.07.2023 14:54:35