Publicidad
Idiomas disponibles
Idiomas disponibles
Safety information
Dangers due to electrical energy
•
Do not connect the workstation frame to the mains electricity until the assembly is complete.
•
Check the electrical equipment in the workstation frame regularly to see that it complies with national
legislation (in Germany, these are the UVV).
•
Do not use any wires with damaged insulation. This will increase the risk of electric shock.
If any wiring is found to be damaged, replace it immediately with
new wiring.
•
Do not position the power feed near any sources of heat.
The persistent heat could damage the wire.
This could easily lead to a fire or a short circuit.
•
Disconnect the workstation frame from the mains electricity if the frame is not in use for an extended
period.
Use of the workstation frame
•
Do not allow children to use the workstation frame unsupervised.
Children may be unaware of the dangers presented by the workstation. They would be in serious danger
of injuring themselves, possibly even with fatal consequences.
•
The workstation frame must only be used in appropriate areas (Assembly instructions).
•
Do not use the workstation frame on an uneven surface.
In such conditions it will not be steady.
•
Keep a break of each height adjustment - take a look at the assembly instructions.
•
Never exceed the maximum load on the workstation frame (
Assembly instructions).
Specific dangers
•
When adjusting the height of the table there is danger of injury. Make sure that there is no-one else in
the immediate surroundings of the frame.
•
When assembling the workstation frame, make sure there is ample space to avoid collisions (i.e.
inclination of roof, fixed objects, filing cabinets, waste-paper bins etc.)in all imaginable directions.
There is a danger of crushing!
•
Make sure there is ample space to avoid collisions if there are objects on the work surface such as
computers or computer peripherals.
•
Make sure there is clearance of at least 25mm from all other furniture,
all around the workstation frame.
In an emergency
•
Leave the immediate surroundings of the workstation frame at once if it starts to move spontaneously.
Under no circumstances attempt to operate the workstation frame.
Have the workstation frame repaired by specialists.
Refrain from using the workstation frame until it has been successfully repaired.
•
Stop using the workstation frame at once if you notice anything unusual (strange sounds, smoke, etc.).
Have the workstation frame repaired by specialists. Refrain from using the workstation frame until it has
been successfully repaired.
•
Stop using the workstation frame at once if its safety features (e.g. up-down switch) fail to work as they
should.
Cleaning
•
Dust the workstation frame once a week with a dry cloth.
•
Clean the workstation frame with a damp cloth and a weak solution of cleaner once a fortnight.
Noise generated by the workstation frame
•
See assembly instructions.
EN
Safety information
Maintenance and upkeep
•
Please be sure that the workstation frame is always in a good condition. For example, have the
workstation frame checked by specialized employees on a regular basis.
•
Do not perform any repairs on the workstation frame or other components yourself.
•
Do not alter the construction of the work surface or its frame.
•
Keep a break of each height adjustment - take a look at the assembly instructions.
•
Any faulty components removed must be replaced with new, original components from the
manufacturer. Use only original replacement parts made by the manufacturer. Have any such work
carried out by a specialist, making reference to this assembly/operating manual.
•
Perform a "reset" at regular intervals - at least once a month - take a look at the assembly
instructions.
Persistent risks
This workstation frame has been built to the state of the art and to recognized safety regulations.
Nonetheless, its use may constitute a risk to the health and safety of users or third
parties, damage to the workstation frame or to other items. The workstation frame
must be used only:
•
for the purpose for which it was intended,
•
if it is completely safe so to do.
Read and keep the operating and installation instructions
•
The operating and installation instructions are part of this table Table. It contains important
information about commissioning and handling.
•
Read the operating and installation instructions, especially the safety instructions, carefully before
inserting the table Table.
•
Failure to follow the operating and installation instructions could result in serious injury or damage
to the table Table.
•
The operating instructions are based on the standards and rules valid in the European Union. Please
also observe country specific guidelines and laws abroad.
•
Keep the operating and assembly instructions near the table for further use. So that you always have
at hand.
•
If you pass on the table to third parties, be sure to include the operating and assembly instructions.
An electronic version of this manual (PDF) is available from our customer service.
WARNING:
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment.
Recycling
•
Taking the workstaon out of acve duty:
Pull the power plug out of the electricity socket.
•
Taking the workstaon apart:
In case of de-assembling please follow the manual backwards or contact customer service.
•
Recycling:
Please split all parts to their type of material. Keep notice of National restrictions!
English
EN
Publicidad
