3M DBI-SALA EZ-STOP AJ512Y/0 Manual De Instrucciones página 10

SAFETY INFORMATION
EN
Please read, understand, and follow all safety information contained in these instructions prior to the use of
this Energy Absorbing Lanyard. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
These instructions must be provided to the user of this equipment. Retain these instructions for future
reference
Intended Use:
This Energy Absorbing Lanyard is intended for use as part of a complete personal fall protection system.
Use in any other application including, but not limited to, material handling, recreational or sports related activities, or other
activities not described in the User Instructions, is not approved by 3M and could result in serious injury or death.
This device is only to be used by trained users in workplace applications.
!
WARNING
This Energy Absorbing Lanyard is part of a personal fall protection system. It is expected that all users be fully trained in
the safe installation and operation of their personal fall protection system. Misuse of this device could result in serious
injury or death. For proper selection, operation, installation, maintenance, and service, refer to these User Instructions
and all manufacturer recommendations, see your supervisor, or contact 3M Technical Services
• To reduce the risks associated with working with an Energy Absorbing Lanyard which, if not avoided, could
result in serious injury or death:
- Inspect the device before each use, at least annually, and after any fall event. Inspect in accordance with the User
Instructions.
- If inspection reveals an unsafe or defective condition, remove the device from service and destroy it.
- Any device that has been subject to fall arrest or impact force must be immediately removed from service. Refer to
the User Instructions or contact 3M Fall Protection.
- Ensure all connecting subsystems (e.g. lanyards) are kept free from all hazards including, but not limited to,
entanglement with other workers, yourself, moving machinery, or other surrounding objects.
- Ensure proper edge protection is used when the device may come into contact with sharp edges or corners.
- Attach the unused leg(s) of the lanyard to the parking attachment(s) on the harness if equipped.
- Do not tie or knot the lanyard.
- Do not exceed the number of allowable users.
- Ensure that fall protection systems/subsystems assembled from components made by different manufacturers are
compatible and meet the requirements of applicable standards, including the ANSI Z359 or other applicable fall
protection codes, standards, or requirements. Always consult a Competent or Qualified Person before using these
systems.
• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or
death:
- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at
height. Consult with your doctor if you have any questions regarding your ability to use this equipment.
- Never exceed allowable capacity of your fall protection equipment.
- Never exceed maximum free fall distance of your fall protection equipment.
- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns
about the use or suitability of the equipment for your application. Contact 3M Technical Services with any questions.
- Some subsystem and component combinations may interfere with the operation of this equipment. Only use
compatible connections. Consult 3M prior to using this equipment in combination with components or subsystems
other than those described in the User Instructions.
- Use extra precautions when working around moving machinery (e.g. top drive of oil rigs), electrical hazards, extreme
temperatures, chemical hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall
onto you or the fall protection equipment.
- Use Arc Flash or Hot Works devices when working in high heat environments.
- Avoid surfaces and objects that can damage the user or equipment.
- Ensure there is adequate fall clearance when working at height.
- Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make
repairs to the equipment.
- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall
incident occurs.
- If a fall incident occurs, immediately seek medical attention for the worker who has fallen.
- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.
- Minimize swing falls by working as directly below the anchorage point as possible.
- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the
trainee to an unintended fall hazard.
- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.
10