Thomas SUPER 30 S Modo De Empleo página 18

Dry vacuuming
THOMAS SUPER 30 S
After wet vacuuming, the appliance must be absolutely dry; dry
off the flexible hose or tubes if necessary beforehand.
Never dry vacuum without filters or with damaged
filters.
Assembly
A Pull out the plug and lift off the motor block (2).
L Then push the cleaning solution tube (37), which is located in
the motor block (2), into the fixture provided for this purpose
(36).
Inserting the filter
G Use the taper filter (25) in addition to the paper filter sack.
By doing this you achieve the best retention of the residue
dust. Place the taper filter (25) on the underside of the motor
head (2). Depending on the model in position 1 or 2 and lock
with the rotary clips. In the case of stubborn dirt weak suction
power the taper filter (25) can be washed out with clear water
without adding washing detergents or cleaning agents. Make
sure that the filter is completely dry when using the vacuum
cleaner the next time.
H Place the filter bag (26) inside the collecting bin, making sure
that the opening located in the cardboard inlay is placed in line
with the suction socket (8).
Then press the filter bag evenly around the sides of the
collecting bin.
D Put the motor block (2) back in position. The control knob on
the appliance must be set at "0".
F Plug the appliance into a mains socket.
Switching on the appliance
M When using the appliance in the dry vacuuming mode, the control
knob (7) must be set at the „carpet + floor nozzle" symbol.
The pilot lamp (6) should not be lit up.
The appliance is ready for use.
THOMAS SUPER 30S AQUAFILTER
Never use your AQUAFILTER appliance in dry vacuum mode
without the Aquafilter, the fine particle textile filter, taper filter
and an appropriate water level.
18 18
Do not vacuum up large quantities of particle dust, e.g. flour,
cocoa powder, cement, etc.
Preparation
A Remove the motor head (2) with the cable disconnected from
the mains plug.
B Remove fresh water tank (28).
L Press the suction hose (37) fitted to the motor head (2) in the
holder (36) provided for this purpose.
G Place the taper filter (25) on the underside of the motor head (2).
Depending on the model in position 1 or 2 and lock with the rotary
clips. In the case of stubborn dirt weak suction power the taper filter
(25) can be washed out with clear water without adding washing
detergents or cleaning agents. Make sure that the filter is completely
dry when using the vacuum cleaner the next time.
I Connect up the three-piece AQUA filter (27), pushing it together until
the two parts fit snugly, and push it firmly onto the suction socket.
Note the marker guides!
The AQUA filter has to snap into place on the floor of the
suction canister and has to lie there evenly.
Fill 2 litres of clear water into the collecting bin.
J Place the fine particle filter (30) on the rim of the suction tank.
D Mount motor head (2). The rotary switch on the appliance must
be set to "0".
F Connect up mains connection cable (10).
To put into operation
Switch on appliance
M The rotary knob (7) must be set to the carpet nozzle symbol
when dry vacuuming.
The pilot lamp (6) should not be lit up.
Appliance is ready to use.
Cleaning and care of the AQUA filter system
For reasons of hygiene, empty, clean and dry the
AQUAFILTER system and the collecting bin after each
use. Dirty water and damp parts will promote the
growth of bacteria and mildew.
Clean the fine particle filter – according to how dirty it is – with
a dry or damp cloth. If it is very dirty, clean it out with clear water,
without adding any detergents or cleaning fluids. Please make sure
that the filter is completely dry before next using the vacuum cleaner.