Publicidad
Idiomas disponibles
Idiomas disponibles
EN
The correct operation of the autodrive control bar must also be checked before
each mowing job. When the autodrive control bar is released, the autodrive must
stop immediately and the mower must come to a standstill. If this is not the case, it
must be checked immediately by an authorised workshop.
Make sure that all protective devices have been attached properly and are not
damaged.
To avoid any risk, always check the condition and firm seating of the blade before
each mowing job. The blade fastening screw must always be tightened by an
authorised workshop. If the blade screw is tightened excessively or insufficiently,
the blade fastening and cutter bar may be damaged or get loose, which can lead to
serious injuries. A worn or damaged blade must imperatively be replaced (see
chapter "Maintenance of the cutter bar").
Check the blade fastening for wear and a tight fit every 10 operating hours Also
check device screws and nuts for a firm fit and re-tighten, if necessary.
If the mower becomes blocked e.g. by colliding with an obstacle, have an
authorised workshop check whether any parts of the mower are damaged or
deformed. Always have any necessary repairs done by an authorised workshop
too.
If the machine starts to vibrate unusually heavily or to make unusual noises, please
have it checked immediately by an authorised workshop.
Time restrictions
In Germany, the time for the operation of lawn mowers is regulated in the "32nd
Ordinance for the Implementation of the Federal Immissions Act (32. BImSch-V)".
In addition, regional restrictions are possible (e.g. to observe the afternoon quiet
hours); related information is available from the competent municipal authority.
Tips on caring for your lawn (figure M)
WARNING
Remove all foreign bodies (stones, wood, branches, etc.) from the lawn
before any mowing; however, you should still keep an eye out for objects
lying around while mowing.
You can get an introduction to lawn care from your dealer on request. Information
and instructions for mowing can also be found on the manufacturer's website.
Mulching
What is mulching?
During mulching, the lawn is cut and the cut stalks are simultaneously repeatedly
shredded by the special mulching knife. This mulch knife straightens the stalks of
grass and cuts the stalks into very short pieces, which are then evenly distributed
over the lawn.
The grass sections can now dry out and rot more quickly, thus promoting humus
formation. In this way, the soil is fertilised in a natural manner and also protected
from drying out. The collection and disposal of the cut material is no longer
necessary. The mulching concept thus substantially supports the ecological cycle.
How to achieve a perfect lawn cut?
When using the mulch mower, the grass height to be cut should not exceed 10 cm,
if possible. In one pass, a maximum of 1/3 of the grass height is cut down. If a
positive result is not achieved, it may be necessary to mulch two times in
succession.
Depending on the type of lawn and the intensity of growth, the lawn should be
mown at regular intervals. Especially during strong growth phases, mulching
requires more frequent mowing than the traditional collection as otherwise this "one
third" rule is difficult to adhere to.
In order to achieve an optimal mulching result, you should reduce the speed of the
machine when mulching compared to traditional mowing, to give the grass time to
stay longer in the mower and to be thus cut several times.
The best cut pattern and result is achieved on a dry lawn, as wet lawn quickly sticks
and clumps due to the short grass sections. These lumps of grass rot and get
mouldy and hinder the desired ecological cycle.
If, nevertheless, the lawn must be mowed when it is very damp or wet, the grass
sections must be shorter, i.e. the cutting height must be set 1-2 steps higher than
for a dry lawn.
You will notice that observing these simple rules, you will get a healthy lawn and the
green waste disposal is no longer necessary.
Information regarding mulching can also be found on the manufacturer's website.
17 SERVICE INTERVALS
IMPORTANT
Avoid damage! Under extreme or unusual conditions, shorter servicing
intervals than the ones specified below may be necessary. If you establish
any problems, please contact an authorised workshop.
Carry out routine servicing on the machine in line with the following servicing
intervals.
Work must be carried out at the following servicing intervals in addition to the
maintenance work listed in these operating instructions.
Before initial use
•
Charge the battery/batteries according to the separate operating instructions
for the charger.
•
Check all screw connections for a tight fit.
•
Check the blade screw and have an authorised workshop tighten it, if
necessary.
•
Check whether the motor stop safety control bar is working properly.
•
Check whether the autodrive control bar is working properly.
•
Check that all protective devices have been attached properly and are not
damaged.
Before every operation
•
Check the lawn area and remove any objects, particularly live wires.
•
Check the area of the boundary wire (if an automatic mower is being used for
lawn care).
•
Check the charge level of the battery/batteries (see chapter "Battery level
indicator").
•
Check the condition and firm fit of the blade; have the blade screw tightened
by an authorised workshop, if necessary.
•
Check whether the motor stop safety control bar is working properly.
•
Check whether the autodrive control bar is working properly.
•
Check that all protective devices have been attached properly and are not
damaged.
•
Check that the air filter is clean and in good condition.
Every 10 operating hours
•
Check all screw connections for a tight fit.
•
Check the blade fastening for wear and a tight fit.
After every operation
•
Clean the mower.
•
Check the blades for damage and wear.
Every 50 operating hours
•
Clean the air filter W.
•
Grease the bearings of the rear wheel drive R.
During annual servicing
•
Have the air filter insert replaced W1.
•
Have the gearbox and the area under the belt cover cleaned.
•
Check all Bowden cables and have them set, if necessary.
18 CARE AND SERVICING FOR YOUR MOWER
Regular care is the best way to guarantee a long service life and problem-free
operation! Insufficient device maintenance will lead to safety-related faults!
Only use original spare parts because only those guarantee safety and
quality!
Cleaning (figure O)
IMPORTANT
For cleaning and maintenance work, switch off the motor unit. To do this,
switch off standby mode (see chapter "SWITCHING STANDBY MODE
ON/OFF") and remove the batteries (1.), only then should you tilt the mower
upwards (2.) O. If it is necessary to place the mower on its side, place it on
the left side and not the right side, as otherwise the motor start on the upper
section of the bar might be actuated.
Secure the mower in the raised position!
Remove all dirt and grass directly after mowing. Use a brush or cloth to clean.
IMPORTANT
Never spray the mower with water. The electrical system may be damaged.
Storage
Always store the device without batteries inserted.
Always store the device in a clean and well-serviced state in a closed, dry room and
inaccessible to children.
12
Safety information!
For explanation of symbols, see the table on
page 5
Publicidad
