Hitachi Koki C10FSH Instrucciones De Manejo página 17

16. Bevel cutting procedures
CAUTION
Ensure that the clamp lever is securely fixed when
beveling.
Please do this if the length of the material being cut
off is more than 25 mm long. Sometimes cutting
cannot be accomplished because the saw blade will
catch on the inside of the lower guard.
(1) Loosen the clamp lever and bevel the saw blade to
the left or to the right. When tilting the motor head to
the right pull the fixing pin towards the rear.
The clamp lever adopts a latchet system. When
contacting the work bench and the main body, pull
the clamp lever in the direction of the arrow mark as
illustrated in Fig. 16, and change the direction of the
clamp lever.
(2) Adjust the bevel angle to the desired setting while
watching the bevel angle scale and indicator, then
secure the clamp lever.
WARNING
When the workpiece is secured on the left or right
side of the blade, the short cut-off portion will come
to rest on the right or left side of the saw blade. Always
turn the power off and let the saw blade stop
completely before raising the handle from the
workpiece.
If the handle is raised while the saw blade is still
rotating, the cut-off piece may become jammed
against the saw blade causing fragments to scatter
about dangerously.
17. Compound cutting procedures
Compound cutting can be performed by following the
instructions in 14 and 15 above. For maximum
dimensions for compound cutting, refer to
"SPECIFICATIONS" table.
CAUTION
Always secure the workpiece with the right or left hand
and cut it by sliding the round portion of the saw
backwards with the left hand.
It is very dangerous to rotate the turntable to the left
during compound cutting because the saw blade may
come into contact with the hand that is securing the
workpiece.
In case of compound cutting (angle + bevel) by left
bevel, turn the sub-fence counterclockwise, and
engage in the cutting operation.
18. Cutting long materials
When cutting long materials, use an auxiliary platform
which is the same height as the holder (optional
accessory) and base of the special auxiliary
equipment.
Capacity: wooden material (W × H × L)
300 mm × 45 mm × 1300 mm, or
180 mm × 25 mm × 2000 mm
19. Installing the holders ... (Optional accessory)
The holders help keep longer workpieces stable and
in place during the cutting operation.
(1) As indicated in Fig. 9, use a steel square for aligning
the upper edge of the holders with the base surface.
Loosen the 6 mm wing nut. Turn a height adjustment
bolt 6 mm, and adjust the height of the holder.
(2) After adjustment, firmly tighten the wing nut and
fasten the holder with the 6 mm knob bolt (optional
accessory). If the length of Height Adjustment Bolt 6
mm is insufficient, spread a thin plate beneath. Make
sure the end of Height Adjustment Bolt 6 mm does
not protrude from the holder.
CAUTION
When transporting or carrying the tool, do not grasp
the holder.
There is the danger of the holder slipping out of the
base. Grasp the handle instead of the holder.
20. Stopper for precision cutting ... (Stopper and holder
are optional accessory)
The stopper facilitates continuous precision cutting
in lengths of 280 mm to 450 mm.
To install the stopper, attach it to the holder with the
6 mm knob bolt as shown in Fig. 10.
21. Confirmation for use Crown molding vise, Crown
molding Stopper (L) and (R) (Optional accessory)
(1) Crown molding Stopper (L) and (R) (optional
accessories) allow easier cuts of crown molding
without tilting the saw blade. lnstall them in the base
both-sides side to be shown in Fig. 18. After inserting
tighten the 6 mm knob bolts to secure the Crown
molding Stoppers.
(2) The crown molding vise (B) (Optional accessory) can
be mounted on either the left fence (Fence (B)) or the
right fence (Fence (A)). lt can unite with the slope of
the crown molding and vice can be pressed down.
Then turn the upper knob, as necessary, to securely
attach the crown molding in position. To raise or lower
the vise assembly, first loosen the 6 mm knob bolt.
As shown in Fig. 19 the vise shaft has three locking
grooves into which the tip of the 6 mm wing bolt is
designed to fit in order to lock the screw holder in the
desired position.
To ensure that the tip of the 6 mm wing bolt is properly
aligned with the desired locking groove on the vise
shaft, simply align the upper surface of the fence to
either of three v-grooves on the vise shaft surface or
to the lower surface of the screw holder.
Therefore, the vise assembly can be attached in either
of three positions to ensure proper height adjustment.
After adjusting the height, firmly tighten the 6 mm
wing bolt; then turn the upper knob, as necessary, to
securely attach the the crown molding in position (See
Fig 19).
Position crown molding with its WALL CONTACT
EDGE against the guide fence and its CEILING
CONTACT EDGE against the Crown molding Stoppers
as shown in Fig. 19. Adjust the Crown molding
Stoppers according to the size of the crown molding.
Tighten the 6 mm wing bolt to secure the Crown
molding Stoppers. Refer to the lower table for the
miter angle.
Use the sub fence (A) to secure the crown molding
more firmly (See Fig. 11).
WARNING
Always firmly clamp or vise to secure the crown
molding to the fence; otherwise the crown molding
might be thrust from the table and cause bodily harm.
Do not bevel cutting. The main body or saw blade
may contact the sub fence, resulting in an injury.
22. Groove cutting procedures
Grooves in the workpiece can be cut by adjusting the
8 mm depth adjustment bolt (Fig. 7).
(1) Loosen the 8 mm wing nut and turn the 8 mm depth
adjustment bolt by hand.
(2) Adjust to the desired cutting depth by setting the
distance between the saw blade and the surface of
the base.
(3) The 8 mm wing nut must be properly tightened after
the adjustment has been completed.
English
16