Hardware Package; Assembly; Stand - Delta 36-725 Manual De Instrucciones

HARDWARE PACKAGE

DESCRIPTION (QTY)
1. M8 x 70mm carriage bolt (1)
2. M8 nylock nut (3)
3. M6 x 72mm carriage bolt (4)
4. M6 nut (4)
5. M8 spring washer (1)
6. M8 x 53mm Axle Pin (2)
7. M6 x 10mm self-tapping bolt (16)
8. 3/16'' hex wrench - T shape (1)
9. 3/16'' hex wrench - L shape (1)
10. 6mm allen hex wrench - L shape (1)
= Item is not shown on the parts list.
*
• Do not lift saw without help. Hold it close to your
body while lifting. Keep knees bent and lift with your
legs, not your back.
• Fully assemble saw with leg assembly prior to use.
Leg assembly is an integral and necessary part of the
support structure for this saw.
• Do not modify saw, or create accessories not
recommended for use with this saw.
• Make sure power switch is in "OFF" position before
connecting to power supply.
• Do not connect to power supply until assembly is
complete
Avoid contact with blade teeth. Keep
blade stored or lowered when possible.

STAND

1. Connect the two tube legs by inserting the end
of the left leg (A) into the end of the right leg (B)
as shown in Figure 1. Secure with a M8 x 70mm
carriage bolt, lock washer
2. Insert the four open ends of the tube legs into the
leg collars (C) as shown. Secure each leg with a
M6 x 72mm bolt and nut.
3. Attach the back and front leg support panels (D) to
the legs using four M6 x 10mm self-tapping bolts.
NOTE: Place screw through small hole first. Snug down
but do not tighten this screw. Place rest of the screws
through the slots and start threading into holes on
mount tab on stand. Once all screws are started,
tighten all four sufficiently to hold plate firmly. These are
self-tapping screws and may be hard to thread at first.
Follow this procedure for all four panels or 16 screws.
UNPACKING
Item #
Parts List
153
155
144
145
154
151
146
*
*
*

ASSEMBLY

and nylock nut and tighten.
(continued)
11. 1/4"-20 x 1/2" hex butt hd screw
w/1/4" spring washer (7)
12. Front rail union plate(1)
13. M5 x16mm shoulder bolt (2)
14. M5 nylock nut (2)
15. 5/16-18 x 7/8 hex screw w/
16. M5 x 6mm Phillips head screw (1)
17. M8 x16 shoulder bolt (4)
18. M8 nylock nut (4)
19. 5/16-18 x 11/8 inch flat head screw (12)
20. 5/16-18 hex flange nut (12)
21. 5/16 lock washer (12)
22. Wire clip: UC-1.5 white (1)
23. Rail alignment gauge (1)
TOOLS REQUIRED FOR ASSEMBLY
(NOT INCLUDED):
• Slotted screwdriver
• Phillips head screwdriver
• 8mm wrench
• 10mm wrench
• 12mm wrench
• 13mm wrench
• 1/2-inch wrench
• 9/16-inch wrench
• 6mm Allen hex wrench
• 5/32-inch Allen wrench
• 3/16-inch Allen wrench
B
D
10
Item #
Parts List
35
32
34
33
(10)
58
spring washer
26
20
21
19
22
23
25
*
A
FIGURE 1
C