Synchronous Control Of Multiple Floodlights (Master / Slave Mode); Copying Sequences Of Scenes; Operation With A Dmx Controller; Dmx Connection - IMG STAGELINE ODW-2410RGBW Manual De Instrucciones

2) Use the button UP or DOWN to select the
number to which the sequence of scenes
is to be stored, and then press the button
ENTER . The display will show the number of
the first scene ( ) .
SC01
3) Press the button ENTER and set the following
parameters:
Brightness of red
ƊRed :
Brightness of green (0 – 255)
green:
Brightness of blue
blue :
Brightness of white (0 – 255)
white:
Flash frequency
strob:
of the stroboscope
Length of scene (time),
Time :
100 = 60 seconds
Crossfading time
Fade :
4) The arrow always precedes the current
Ɗ
selection or the value to be set . To set the
parameter selected: Press the button ENTER
and use the button UP or DOWN to change
the setting; then press the button MENU
to return to the parameter selection and to
change another parameter .
Notes:
1 . The length of a scene must at least be set to
the value 001; otherwise, it is not possible to
program the subsequent scene .
2 . To crossfade from one scene to the next, a cross-
fading time must be set for both scenes .
5) Once the first scene has been set, press the
button MENU repeatedly until the arrow
points to the number of scene (
the button UP to select the second scene,
press the button ENTER, set the scene and
then repeat this procedure for all subsequent
scenes .
6) Once the final scene has been set, store the
sequence of scenes: Immediately after setting
a parameter, keep the button ENTER pressed
for 5 seconds . When the button is released,
the number of the sequence (
) will appear on the display; if not,
Pro.10
the button ENTER has not been pressed long
enough .
Notes:
1 . A sequence of scenes must have been completely
programmed before the floodlight is disconnected
from the power supply . After the floodlight has been
switched on again, the sequence of scenes cannot
be changed anymore; it can only be programmed
again . To overwrite a sequence of scenes, it is not
necessary to delete the previously programmed
scenes first .
2 . When the sequence of scenes is not called up by
means of the control buttons (4) [chapter 7 .3 .] but
via a DMX light controller, DMX channel 2 will define
the length of a scene and DMX channel 3 will define
the crossfading time (chapter 10 .1 .7) . Channel 2
must be set to a DMX value > 0; otherwise, the
floodlight will remain dark .
7.5 Synchronous control of multiple
floodlights (master / slave mode)
Multiple ODW-2410RGBW can be intercon-
nected . The master unit will then synchronously
control all slave units .
1) Use the inline jack (9) of the cable DMX OUT
and the plug (6) of the cable DMX IN to connect
the floodlights in a chain . Please refer to chap-
ter 8 .1, "DMX connection", skipping step 1 .
2) The floodlight is factory-set to act as a slave
unit in master / slave mode . Thus, only the
floodlight that is to control the slave units
must be defined as a master unit .
Call up the menu item
setting . The display will show the following:
= master unit
DMX
= slave unit
ƊSlave
An arrow will point to the current setting .
If required, use the button UP or DOWN to
change the setting .
(0 – 255)
3) Set the master unit to the operation mode
desired ( ☞
(0 – 255)

7.5.1 Copying sequences of scenes

The programmed sequences of scenes of a unit
(0 – 20 Hz)
(chapter 7 .4 .) can be copied to other units . This
is useful when multiple units are to run inde-
pendently with the same sequences of scenes .
For synchronous operation on interconnected
units (chapter 7 .5), it is not necessary to copy
the sequences of scenes .
Define the unit whose sequences of scenes
are to be copied as a master unit and connect it
to the other units (
other units as slave units:
1) At the slave units that are to adopt all se-
quences of scenes from the master unit, call
up the menu item
.
ƊSlave
2) At the master unit, call up the menu item
and the submenu item
SET
will appear on the display .
word:
3) Press the following buttons:
UP, DOWN, UP, DOWN .
) . Use
ƊSC01
For each press of a button, an asterisk
appear on the display .
4) Use the button ENTER to start copying . Dur-
ing the copy process, the slave units will light
up in yellow; they will light up in red in case
of an error; and they will light up in green
once the copy process has been successfully
completed .
... Note: The sequences of scenes copied will only be
Pro.01
available after a different sequence of scenes has been
selected or after the power supply has been inter-
rupted .
8 Operation with a
DMX Controller
DMX (Digital Multiplex) means digital control of
multiple DMX units via a common control line .
For operation by means of a DMX light con-
troller (e . g . DMX-1440 or DMX-510USB from
IMG STAGELINE), the floodlight is equipped
with 11 DMX control channels . However, it can
also be controlled by 10, 6, 5, 4 or 3 channels,
if required . The functions of the channels and
the corresponding DMX values can be found in
chapter 10 .1 .

8.1 DMX connection

For DMX connection, 3-pole XLR connections
with the following pin configuration are avail-
able:
pin 1 = ground, 2 = DMX−, 3 = DMX+
For the connection, special cables for DMX signal
transmission (e . g . cables of the CDMXN series
from IMG STAGELINE) should be used . For cable
lengths exceeding 150 m and for the control of
more than 32 units via a single DMX output,
the insertion of a DMX level matching ampli-
fier (e . g . SR-103DMX from IMG STAGELINE) is
recommended .
to change the
RUN
chapters 7 .1 – 7 .3) .
☞ chapter 7 .5); set up the
and set the option
RUN
.
UPLD Pass­
will
*
1) Connect the plug (6) of the cable DMX IN to
the inline jack of the cable supplied that is
fitted with the XLR plug (10), and then use
the cap nut to screw the plug-in connection
together . Using an extension cable, connect
the XLR plug to the DMX output of the light
controller or, if additional DMX-controlled
units are used, to the DMX output of another
DMX-controlled unit .
2) If additional floodlights ODW-2410RGBW
are used, use the inline jack (9) of the cable
DMX OUT to connect the first floodlight to
the plug (6) of the cable DMX IN of the sec-
ond floodlight . Proceed in the same way to
connect the second floodlight to the third
one etc . until all floodlights are connected
in a chain .
If the DMX connection cables between
the floodlights are too short, use suitable
extension cables, e . g .
ODP-34DMX (length: 2 m) or
ODP-34DMX /10 (length: 10 m) .
To connect other DMX-controlled units, use
the adapter cable fitted with the XLR inline
jack .
3) To prevent interference in signal transmis-
sion: For long cables or for a great number
of units connected in series, terminate the
DMX output of the last DMX unit in the chain
with a 120 Ω resistor (> 0 .3 W): Connect an
appropriate terminating plug (e . g . DLT-123
from IMG STAGELINE) to the XLR inline jack
of the supplied adapter cable . For outdoor
installation, protect the XLR inline jack and
the terminating plug against humidity .

8.2 Setting the DMX operation mode

To operate the ODW-2410RGBW by means
of a light controller, set the DMX start address
( ☞ chapter 8 .3) and the DMX operation mode .
The DMX operation mode selected will deter-
mine the number of the DMX channels required
(3 – 11 channels) . Please refer to chapter 10 .1
for the functions that can be controlled with
the respective DMX operation modes, and then,
based on this information or based on the num-
ber of the control channels available at the light
controller, select the DMX operation mode:
1) Call up the menu item
Personality
2) The following settings are available:
Setting Number of DMX channels
11 channels /10 channels without
ƊStage
subaddressing (☞ chapter 10.1.7)
3 channels
Arc.1
1 = red, 2 = green, 3 = blue
4 channels
Ar1.d
1 = dimmer, 2 = red, 3 = green, 4 = blue
4 channels
Arc.2
1 = red, 2 = green, 3 = blue, 4 = white
5 channels
1 = dimmer, 2 = red, 3 = green,
Ar2.d
4 = blue, 5 = white
6 channels
1 = dimmer, 2 = red, 3 = green,
Ar2.s
4 = blue, 5 = white, 6 = stroboscope
3 channels
1 = colour, 2 = colour saturation,
HSV
3 = brightness
Fig. 4 Number of DMX channels
3) The arrow points to the current setting .
Ɗ
Use the button UP or DOWN to change the
setting .
.
11