Standard Accessories; Battery Removal/Installation; Prior To Operation - Hitachi Koki DV14DVF Instrucciones De Manejo

English

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains the
accessories listed in the table below.
1 Plus driver bit (No. 2 × 65L) .................... 1
2 Charger (UC18YG or UC18YK) .............. 1
DV14DVF
3 Battery .................................................... 2
DV18DVF
or
Battery .................................................... 3
4 Plastic case ............................................ 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
1. Battery (EB1414S, BCC1412)
(For DV14DVF)
2. Battery (EB1814SL, BCC1812)
(For DV18DVF)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Drilling of brick and concrete block, etc.
○ Driving and removing of machine screws, wood screws,
tapping screws, etc.
○ Drilling of various metals.
○ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch (2 pcs.)
to remove the battery (see Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger power cord to the receptacle
Connecting the power cord will turn on the charger.
2. Insert the battery into the charger
Insert the battery fi rmly while observing its direction,
until it contacts the bottom of the charger (See
Fig. 3). (The pilot lamp lights up.)
CAUTION
If the pilot lamp does not light up when the battery is
inserted, pull out the power cord from the receptacle
and check the battery mounting condition.
(1) Regarding the temperatures of the rechargeable battery
The temperatures for rechargeable batteries are as
shown in Table 1.
Table 1 Recharging ranges of batteries
Rechargeable batteries
EB1414S, EB1814SL,
BCC1412, BCC1812
10
Temperatures at
which the battery
can be recharged
0°C – 45°C
(2) Regarding time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 2.
Table 2 Charging time (At 20°C)
Charger
Battery
EB1414S, EB1814SL,
BCC1412, BCC1812
The pilot lamp goes off to indicate that the battery is fully
charged.
The battery charging time becomes longer when a
temperature is low or the voltage of the power source is
too low.
When the pilot lamp does not go off even if more than 120
minutes have elapsed after starting of the charging, stop
the charging and contact your HITACHI AUTHORIZED
SERVICE CENTER.
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may not
light up. At that time, cool the battery fi rst, then start
charging.
3. Disconnect the charger's power cord from the
receptacle
4. Hold the charger fi rmly and pull out the battery
NOTE
After charging, pull out batteries from the charger fi rst,
and then keep the batteries properly.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after use.
If such a battery is recharged immediately after use, its
internal chemical substance will deteriorate, and the
battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.

PRIOR TO OPERATION

1. Setting up and checking the work environment
Check if the work environment is suitable by following the
precautions.
UC18YG UC18YK
Approx. Approx.
30 min. 50 min.