Section 5. Operating Instructions; Control Panel; Turning Power Pack On/Off (Manually); Select Language - Zodiac Jandy Pro TruClear Manual De Instalación Y Funcionamiento

Page 20
ENGLISH
Table 2.
Current
Cyanuric Acid
10,000 gal (38,000 L ) 15,000 gal (57,000 L) 20,000 gal (76,000 L ) 25,000 gal (95,000 L ) 30,000 gal (114,000 L) 35,000 gal (132,000 L )
Level - ppm
0 (4.2 lbs) 1.9 kgs
10 (3.4 lbs) 1.5 kgs
20 (2.5 lbs) 1.1 kgs
30 (1.7 lbs) 0.8 kgs
40 (0.8 lbs) 0.4 kgs
NOTE
For indoor pools, it is not necessary to add chlorine stabilizer to the swimming pool water.

Section 5. Operating Instructions

5.1 Control Panel

5.2 Turning Power Pack On/Off (Manually)

To turn the Jandy Pro Series chlorine generating device To turn the Jandy Pro Series chlorine generating device
on or off press the button.
A quick press will place the chlorinator into "standby"
state. While in "standby" mode a quick press will return
to "chlorinating" mode. If held down for 6 seconds it
will completely power down.
NOTE
Because the power pack is wired to the pump's power
source, the power pack can only be turned on when the
pump is turned on.
In normal operation, the up and down arrows are used to set the output level of the chlorinator.
The output should be adjusted in order to achieve the desired Free Available Chlorine level of 2-4 ppm.
The back/save button will save any changes you have made in the menu and send you back to the previous
menu screen. The select button will scroll through and open any available parameters for editing.
*When connected to an automation system via RS485, full control of the TruClear system is given over to
the automation controller. No functionality will persist at the TruClear UI. In order to control the TruClear
from the UI, the automation system must fi rst be placed into service mode. For details on service mode
please consult the operation manual for the controller you are using as follows:
● AquaLink RS: 6594 ● Z4: H0386500 ● PDA: H0572300
®
Jandy Pro Series TruClear
®
Approximate Pounds and Kilograms of Stabilizer Needed to Obtain 50 ppm
(6.3 lbs) 2.9 kgs (8.4 lbs)
(5.1 lbs) 2.3 kgs (6.7 lbs)
(3.8 lbs) 1.7 kgs (5.1 lbs)
(2.5 lbs) 1.2 kgs (3.4 lbs)
(1.3 lbs) 0.6 kgs (1.7 lbs)
∞ DISPLAY
Shows TruClear™ status and chlorine
production percentage.
Indicates TruClear is in standby mode
and will not be producing chlorine even
if the filter pump is running.
Indicates TruClear has detected filter
pump activation and is initiating chlorine
production.
Indicates TruClear is currently producing
chlorine and displays current production
output percentage.
Indicates TruClear is connected to a
remote automation system via RS485*.
Press to turn power to system on. Press and hold
for 6 seconds to completely power the system
down. A single quick press will toggle the system
from Standby to Auto mode when not connected
to a remote automation system via RS485*.
Chlorine Generating System
™
Pool/Spa Size US Gallons (Litres)
3.8 kgs (10.5 lbs) 4.8 kgs (12.6 lbs) 5.7 kgs (14.8 lbs) 6.7 kgs
3.1 kgs (8.4 lbs) 3.8 kgs (10.1 lbs) 4.6 kgs (11.8 lbs) 5.4 kgs
2.3 kgs (6.3 lbs) 2.9 kgs
1.5 kgs (4.2 lbs) 1.9 kgs
0.8 kgs (2.1 lbs) 1.0 kgs

5.3 Select Language

5.3 Select Language
Press and hold the
simultaneously for fi ve seconds
to access the service menu. Use the
select language. Press the
selection has been made.
5.4 Turning Power Pack On/Off (Using the
Pump's External Timer)
If the power pack is wired to the pump's external timer
and the power to the unit is on, the power pack will
automatically turn on and off when the pump turns
on and off (see Section 3.5). When the power pack is
wired as such, the only setting that must be
set manually is the chlorine output level (see
Section 5.4).

5.5 Chlorine Output Level

When setting the chlorine output level, the
factors to consider are:
- number of gallons in the pool
- number of bathers (bather load)
- amount of pollen and dust going in the water
- number of hours the pump runs
- whether you are using a single or variable
speed pump
- climate and water temperature
- amount of rain water entering the pool.
A good starting point for pools at 15K gallons
and under should be 40%. Pools closer to the
25K to 30K gallons
should use 60% as a
starting point.
If you fi nd that these levels do not provide
the 1 - 3 PPM chlorine residual that is
desired, then raise the output level higher to
compensate.
If you fi nd that output level is approaching
90% to 100% and testing the pool water
shows no or very low chlorine residual, your
pool may need to be manually shocked due to
a waste load that has built up in the pool water
that is overwhelming the chlorine you are
|
Installation & Operation Manual
(7.6 lbs) 3.4 kgs (8.9 lbs)
(5.1 lbs) 2.3 kgs (5.9 lbs)
(2.5 lbs) 1.2 kgs (3.0 lbs)
buttons
button to
button to exit when your
4.0 kgs
2.7 kgs
1.3 kgs