Sanding Pad Brake; Accessories; Environment; General Information - Festool PLANEX LHS 2 225 EQI Manual De Instrucciones

Customer service and repairs must
only be carried out by the manufac­
turer or service workshops. Find the
nearest address at:
www.festool.co.uk/service
Always use original Festool spare
EKAT
4
parts. Order no. at:
www.festool.co.uk/service
5
3
2
1
– Always state the serial number on the
name plate [1-1] of the handle when having
the tool serviced and repaired.
– Check the plug and cable on a regular ba­
sis and, if they are damaged, have them re­
placed by an authorised customer service
workshop.
– Do not clean the power tool with com­
pressed air.
– To ensure constant air circulation, always
keep the cooling air openings in the motor
housing clean and free of blockages.
– Vacuum the backing pad regularly.
– Keep all parts of the tool clean, especially
the controls and housing openings, and
clean them regularly with a brush.
9.1

Sanding pad brake

The sanding pad brake brushes off the sanding
pad and prevents uncontrolled turning of the
sanding pad. The sanding pad brake is almost
wear-free thanks to the pins used.
In the case of a decreasing braking effect, first
check the sanding pad for wear and replace it if
necessary, see Section
If the sanding pad brake is damaged, it must be
replaced by an authorised service workshop.

10 Accessories

Always use original Festool tools and accesso­
ries. Using low-quality tools or accessories
from other manufacturers may increase the
risk of injury and seriously unbalance the ma­
chine, decreasing the quality of the working re­
sults and accelerating power tool wear.
Refer to the Festool catalogue for the order
numbers of accessories and tools or find them
online at www.festool.co.uk.

11 Environment

There is a Li-ion button cell behind the
Bluetooth button [1-2] (only LHS 2 225 EQI) on
®
the handle [1-1].
7.4 .
Before disposal
Qualified specialist only: Remove the Li-ion but­
ton cell from the tool. To do so, unscrew the
housing components and remove the Li-ion
button cell.
Do not dispose of the device in the
household waste! Recycle devices, ac­
cessories and packaging. Observe appli­
cable national regulations.
EU only: In accordance with EU directives on
waste electrical and electronic equipment and
batteries and accumulators and their imple­
mentation in national law, faulty or used elec­
trical equipment, batteries and battery packs
must be collected separately and recycled in an
environmentally friendly manner.
Used or faulty batteries must only be returned
to collection points if discharged and secured
against short-circuiting (e.g. by insulating the
terminals with adhesive tape). The applicable
regulations must be observed.
Batteries will then be recycled.
Information on REACH: www.festool.com/reach

12 General information

12.1 Information on data privacy

The power tool contains a chip which automati­
cally stores machine and operating data. The
data saved cannot be traced back directly to an
individual.
The data can be read in a contactless manner
using special devices and shall only be used by
Festool for fault diagnosis, repair and warranty
processing and for quality improvement or en­
hancement of the power tool. The data shall not
be used in any other way without the express
consent of the customer.
12.2 Information about Bluetooth
LHS 2 225 EQI)
The tool can be connected via Bluetooth
mobile device or a mobile dust extractor. As
soon as the tool is connected to the Festool
Work app via Bluetooth
nection has been authorised, the tool will con­
nect automatically to the Festool Work app
from this point onwards. The tool then regularly
sends status information (ID, operating status,
etc.) via Bluetooth .
®
The Bluetooth word mark and the logos are
®
registered trademarks of Bluetooth SIG, Inc.;
they are used by TTS Tooltechnic Systems AG &
Co. KG, and therefore by Festool, under licence.
English
(only
®
to a
®
and the secure con­
®
25