Standard Accessories; Prior To Operation - Hitachi CS 30Y Instrucciones De Manejo

English
SPECIFICATIONS
Model
Guide bar length (Max. cutting length)
Guide bar Type
Voltage (by areas)*
1
Power Input*
1
No-load chain speed
Type of chain
Chain pitch / Gauge
Sprocket
Oil pump
Chain oil tank capacity
Overload protection
Chain brake
Weight*
2
* Be sure to check the nameplate on product as it is subject to change by areas.
1
* Weight: According to EPTA-Procedure 01/2003
2

STANDARD ACCESSORIES

(1) Chain case .................................................................. 1
(2) Guide bar ..................................................................... 1
(3) Chain ........................................................................... 1
(4) Plug clip*...................................................................... 1
* Not supplied in certain sales areas.
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Chain Saw Oil
(2) Round File
(3) Depth Gauge Jointer
Round File and Depth Gauge Jointer are to be used
for sharpening of chain blades. As to its application,
please refer to the item titled "Sharpening of the Chain
Blade".
(4) Chain Case
Always keep the chain cover on the chain while carrying
the chain saw or while storing it.
Optional accessories are subject to change without notice.
APPLICATIONS
○ General wood cutting.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
12
CS30Y CS35Y
300 mm 350 mm
P012-50CR P014-50CR
(110 V, 220 V, 230 V, 240 V)
110 V: 1560 W
91PX-45 91PX-52
(Oregon) (Oregon)
9.53 mm (3/8") / 1.27 mm (0.05")
5.2 kg 5.4 kg
3. Extension cord
When the work area is remote from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Confi rm the chain tension
Improper chain tension may result in damage to the
chain and the guide bar, and could cause a serious
accident. Always confi rm that there is proper tension on
the chain prior to operation.
5. Fill the oil tank with oil
This unit is shipped without oil in the oil tank.
Prior to operation, remove the oil cap and fi ll the tank
with accessory oil.
This unit is shipped without oil in the oil tank.
Prior to operation, remove the oil cap and fi ll the tank
with chain saw oil (sold separately), or SAE 20 or 30
motor oil. Do not use stained or degraded motor oil.
Check oil reservoir periodically and keep it fi lled while
running saw.
6. It is recommended to use an earth-leakage circuit
breaker or a residual current device.
SAW CHAIN AND GUIDE BAR ASSEMBLY
WARNING
○ Don't use the saw chain or the guide bar other than
those specifi ed in "SPECIFICATIONS".
○ Make sure the switch is turned off and the plug
disconnected from the socket.
○ Always wear gloves when handling the saw chain.
○ The tightening tension for the special nut has been
adjusted to the optimal level. Do not loosen it or tighten
it under any circumstances.
1. Removing the Saw Chain
(1) Check to make sure the chain brake has been released
before removing the side cover. (Fig. 2)
(2) Loosen the knob slightly and then loosen the tension
dial to release the tension on the saw chain. (Fig. 3)
(3) Completely loosen the knob and gently remove the side
cover.
(4) Gently remove the guide bar and saw chain.
CS40Y
400 mm
P016-50CR
220 V, 230 V, 240 V: 2000 W
14.5 m/s
91PX-57
(Oregon)
Number of teeth: 6
Automatic
150 ml
Electrical
Manually actuated
5.4 kg
CS45Y
450 mm
P0H18-50CR
91PX-64
(Oregon)
5.5 kg