Lcd Display - JB Systems TMC-200 Manual De Instrucciones

ENGLISH
 In scratch mode (SCRATCH button (28) activated) the jog wheel is used to manipulate playback of
the music in real time. As a result you can scratch the music on your CD the way you do this with a
normal analog vinyl record. To match the vinyl feel as close as possible and largely improve scratch
performance, the the jog-wheel uses a patented touch-sensitive technology!
 You can manipulate the DSP-effects while they are used in manual mode, see EFFECT buttons (14).
28. SCRATCH button: Used to put the TMC200 in scratch mode. This option gives you the possibility to
scratch any track on the CD in real time. You can use the scratch function in both play and pause mode:
 In play mode: The music plays normally until you touch the big jog wheel(27). While manipulating
the jog wheel(27), the scratch effect is audible. Once the jog wheel is stopped, the music
continues playing from the point where you stopped turning it.
 In pause mode: the music is paused for as long as the jog wheel(27) isn't moved. When you start
manipulating the jog wheel(27), the scratch effect is audible. Once the jog wheel is stopped, the
music stops playing and waits in pause mode.
NOTE: during scratch mode you can switch between play and pause mode by simply pressing the
PLAY/PAUSE button(8)
29. Audio output: Output for the audio signals from the CD-player. Use the supplied cinch/cinch cable to
connect this output to a CD/line input of your mixing unit.
30. Digital out socket: Use this connector to connect the digital signal (S/PDIF format) to the input of a
digital amplifier or digital recorder (ex. Mini disc)
31. RELAY Socket: you can use this connector in two ways: you can use it with the fader start option on
certain mixers or you can connect two TMC200 players together to obtain the relay play function.
 Relay play: Use the supplied mono mini jack/jack cable to connect the RELAY sockets of two
TMC200 players together. Look further in this manual to learn how to perform the relay play
function.
 Fader start: If you are using a mixer with fader start function, use the supplied mono mini
jack/jack cable to connect the player with the fader start of the mixer. Please note that this socket
must never be connected with any voltage.
Attention: This remote control is only compatible with certain (Synq® or Pioneer® compatible)
mixers. Mixers with remote starts functioning with a signal switched to ground will not work.
32. POWER ON/OFF switch: switches the TMC200 on and off.
33. MAINS INPUT: connect the CD player to the AC mains, using the supplied power-cord.
JB SYSTEMS®
USER MANUAL
7/77
ENGLISH

LCD DISPLAY

1. PLAY: appears while the unit is playing a CD.
2. PAUSE: appears while the player is in pause or cue mode.
3. TOUCH INDICATOR: appears when the touch sensitive part of the jog wheel is active.
4. ANTI SHOCK AND BUFFER INDICATOR: The memory status is represented on the display by a
bucket being filled up or emptied. The bucket itself represents that the instant start function is available.
If the bucket is flashing, the instant start is not available. Each segment within the bucket represents
about 2 seconds of anti shock protection.
5. CUE: appears when the master cue point is programmed.
6. PITCH DISPLAY: Shows the actual percentage of speed change, selected with the SPEED slider(20).
7. TIME BAR: shows either time remaining or elapsed depending on the setting of the TIME button(23).
Starts flashing at the end of each track to alert the user to take action.
8. FRAME: Shows "frame" time information of current track. (1 frame = 1/75
9. SECOND: Shows "seconds" time information of current track.
10. MINUTE: Shows "minutes" time information of current track.
11. ELAPSED, TOTAL REMAIN: indicates that the time shown on the display is the track elapsed,
remaining or total remaining time.
12. RELOOP: appears when the loop is played. (repeating a particular area)
13. LOOP: shows when a loop is programmed. You can return to the loop with the reloop button(6).
14. SINGLE: appears when the unit is set to play just one track at a time. When it is not shown, the CD
plays continuously through all tracks. The function is controlled by the SGL/CTN button(24).
15. TRACK / FOLDER: Shows current track or folder number.
16. VISUAL MARKER: indicates the play position in frames: a full rotation equals 95 frames. The marker
moves clockwise in normal play mode and counter-clockwise when the track plays backwards. In pause
mode the marker stops moving.
17. AUTO CUE: The display shows "A.CUE" when the auto cue function is active.
18. AUTO BPM: This indicator is always on present to indicate that the automatic beat counter is working.
19. PITCH LOCK: when Master Tempo is active, the display shows a small "lock" to indicate that the pitch of
the music is locked.
20. CD/MP3: indicates if you have loaded a normal digital audio or MP3 CD.
21. ALPHANUMERIC DISPLAY: Shows the names of folders and MP3 tracks. For MP3 tracks recorded in
CBR also the bit rate is shown. For VBR recorded MP3 tracks the display only shows "VBR".
22. BPM/PARAMETER: The automatic beat counter shows the number of Beats Per Minute on the display.
When the effects are activated, this part of the display shows the applied effect parameters.
TMC200 JB SYSTEMS®
USER MANUAL
th
sec.)
8/77 TMC200