Drying Of A Wheel; Additional Drying Cycles; Special Programs; Short Washing Program And Relative Drying Phase - TECO LR400 Manual De Instrucciones

5.4

DRYING OF A WHEEL

• Once the washing cycle has completed (or at any time during the washing cycle if the "DRY" button is depressed), the LCD display will
show "DRYING" and the pump motor stops while the driving motor will continue rotating keeping the wheel spinning.
• The blue LED by the button corresponding to chosen washing cycle will turn off and the blue LED by the "DRY" button will turn on.
• After a short while a 20 second drying time will start during which compressed air drawn from the compressed air hook-up will be alterna
tively directed to the two sides of the wheel through the blowing nozzles mounted on the two sidewalls of the washing chamber removing
the water and the granules form the sides of the wheel. The LCD display will show "DRYING" on the first line and the time remaining to
completion of the drying cycle on the second line.
• At the end of the drying cycle the compressed air blowing and the driving motor are stopped and the blue led by the "DRY" button turns off.
• The LCD display will show "STOPPING" on the first line while the driving motor comes to a stop, then quickly revert to the main operation page.
CAUTION
Pressing the red "sToP" button at any time during the drying cycle will make the LCd display show "sToPPINg" on the first line while
the driving motor comes to a stop.
After a short while the LCd display will revert to the main operation page.
NOTE
Closing the washing chamber door and pushing the green "RESET" button will make the LCD display show "WAIT" for 5 seconds, then the opera-
ting cycle being performed will restart form the point where it was interrupted.
5.5

ADDITIONAL DRYING CYCLES

The wheel washer can perform a standalone 20 second drying cycle without first going through any washing cycle. This is especially useful in case
the drying cycle performed at the end of a washing cycle didn't remove completely water from the wheel, as can be the case if compressed air
supply to the wheel washer has poor flow capacity.
To perform such a standalone drying cycle:
• Introduce the wheel inside the washing chamber as specified at the beginning of the "WASHING OF A WHEEL" paragraph, then push the
"DRY" button.
• The blue LED by the "DRY" button will turn on and the LCD display will show "STARTING" on the first line and the driving motor will start
rotating leading the wheel to spin.
• After a short while a 20 second drying time will start during which compressed air drawn from the compressed air hook-up will be alterna
tively directed to the two sides of the wheel through the blowing nozzles mounted on the two sidewalls of the washing chamber removing
the water and the granules form the sides of the wheel. The LCD display will show "DRYING" on the first line and the time remaining to
completion of the drying cycle on the second line.
• At the end of the drying cycle the compressed air blowing and the driving motor are stopped and the blue LED by the "DRY" button turns off.
• The LCD display will show "STOPPING" on the first line while the driving motor comes to a stop, then revert to the main operation page.
CAUTION
Pressing the red "sToP" button at any time during the drying cycle will make the blue led by the "drY" button turn off and the LCd
display show "sToPPINg" on the first line while the driving motor comes to a stop. After a short while the LCd display will revert to the
main operation page.
CAUTION
While performing either a washing, an additional drying cycle or the fast warming cycle (read further in this manual for information about
the fast warming cycle and how to perform it), opening the washing chamber door will make the red led by the LCd display turn on and
the LCd display show "sToPPINg" on the first line while the pump and drive motor come to a stop.
NOTE
Closing the washing chamber door and pushing the green "RESET" button will make the LCD display show "WAIT" for 5 seconds, then the opera-
ting cycle being performed will restart form the point where it was interrupted.
6.

sPECIAL ProgrAms

SPECIAL PROGRAMS
RESET + 30" → 10" WASHING CYCLE
RESET + 120" → 600" WASHING CYCLE
RESET + DRY → SERVICE PAGE
RESET + WHS → FAST WATER HEATING
RESET + 60" → GRANULE COLLECTION
6.1

shorT WAshINg ProgrAm ANd rELATIvE drYINg PhAsE

110mm
The wheel washer can perform a 10 second washing cycle (also named PRE-WASHING) followed by a 20 second drying cycle. This is especially
useful to remove the bulk of dust from a wheel after a long warehousing stay, after dismounting it from a vehicle or prior to changing the tire to redu-
ce dust runoff during tire changing.
To perform such a short washing cycle:
• Push the green "RESET" and keep it depressed, then push the " 30" " button contemporarily.
• The LCD display will show "STARTING" on the first line and the driving motor will start rotating leading the wheel to spin.
• After a few seconds the pump motor will start and the pump will draw water and plastic granules form the machine body and send them to the
washing nozzles mounted on the two sidewalls of the washing chamber, that will in turn divert them towards the spinning wheel. The LCD display
will show "WASHING" on the first line and the time remaining to the end of the washing cycle.
40
Adesivo cod. 4-602877
UNICA FUSTELLA - DUE ADESIVI SEPARATI
D
= Min 10mm
AIR
D = 65mm