Long Washing Program And Relative Drying Phase; Heating Device Usage (If Available) - TECO LR400 Manual De Instrucciones

CAUTION
Pressing the red "sToP" button at any time during the washing cycle will make the LCd display show "sToPPINg" on the first line, while
the pump motor and the driving motor come to a stop.
After a short while the LCd display will revert to the main operation page.
• Once the washing cycle has completed (or at any time during the washing cycle if the "DRY" button is depressed the LCD display will show
"DRYING" and the pump motor stops while the driving motor will continue rotating keeping the wheel spinning.
• The blue LED by the "DRY" button will turn on.
• After a short while a 20 second drying time will start during which compressed air drawn from the compressed air hook-up will be alternatively
directed to the two sides of the wheel through the blowing nozzles mounted on the two sidewalls of the washing chamber removing the water and
the granules form the sides of the wheel. The LCD display will show "DRYING" on the first line and the time remaining to completion of the drying
cycle on the second line.
• At the end of the drying cycle the compressed air blowing and the driving motor are stopped and the blue LED by the "DRY" button turns off.
• The LCD display will show "STOPPING" on the first line while the driving motor comes to a stop, then quickly revert to the main operation page.
CAUTION
Pressing the red "sToP" button at any time during the drying cycle will make the LCd display show "sToPPINg" on the first line while
the driving motor comes to a stop.
After a short while the LCd display will revert to the main operation page.
6.2

LoNg WAshINg ProgrAm ANd rELATIvE drYINg PhAsE

The wheel washer can perform a 10 minute washing cycle (also named CONTINUOUS WASHING) followed by a 20" drying cycle. This is especial-
ly useful for wheels that haven't been washed for a long time where the dirt has strongly attached to the rim surface, especially on the inner side,
where most of the braking dust will concentrate.
To perform such a long washing cycle:
• Push the green "RESET" and keep it depressed, then push the " 120" " button contemporarily.
• The four blue LEDs by the 30", 60", 90 and 120" buttons will turn on and the LCD display will show "STARTING" on the first line and the
driving motor will start rotating leading the wheel to spin.
• After a few seconds the pump motor will start and the pump will draw water and plastic granules form the machine body and send them to
the washing nozzles mounted on the two sidewalls of the washing chamber, that will in turn divert them towards the spinning wheel.
• The LCD display will show "CONT. WASHING" on the first line and the time passed since the beginning of the washing cycle.
CAUTION
Pressing the red "sToP" button at any time during the washing cycle will make the four blue LEds by the 30", 60", 90 and 120" buttons
turn off and the LCd display show "sToPPINg" on the first line, while the pump motor and the driving motor come to a stop.
After a short while the LCd display will revert to the main operation page.
• Once the washing cycle has completed or at any time during the washing cycle if the "DRY" button is depressed, the LCD display will
show "DRYING" and the pump motor stops while the driving motor will continue rotating keeping the wheel spinning.
• The four blue LEDs by the 30", 60", 90 and 120" buttons will turn off and the blue LED by the "DRY" button will turn on.
• After a short while a 20 second drying time will start during which compressed air drawn from the compressed air hook-up will be alternatively
directed to the two sides of the wheel through the blowing nozzles mounted on the two sidewalls of the washing chamber removing the water and
the granules form the sides of the wheel. The LCD display will show "DRYING" on the first line and the time remaining to completion of the drying
cycle on the second line.
• At the end of the drying cycle the compressed air blowing and the driving motor are stopped and the blue LED by the "DRY" button turns off.
• The LCD display will show "STOPPING" on the first line while the driving motor comes to a stop, then revert to the main operation page.
CAUTION
Pressing the red "sToP" button at any time during the drying cycle will make the LCd display show "sToPPINg" on the first line while
the driving motor comes to a stop.
After a short while the LCd display will revert to the main operation page.
6.3 WATEr hEATINg sYsTEm UsAgE (vErsIoN h)
The wheel washer can be equipped at manufacturing with a 4 kW (5,4 Hp) 3-phase heating system with an integrated water temperature control
(available on demand). The water heating system operation is entirely controlled by the computer controlling the whole operation of the wheel
washer.
The integrated temperature control is set to stop operation of the water heating system when the water temperature reached 50 °C (122 °F) and to
start it again when the water temperature falls below 47 °C (116 °F). This water temperature range is set by the manufacturer and provides optimal
washing and drying results while preventing burning hazard to the operator.
The wheel washer is equipped also with a TIMING FEATURE to start operation of the water heating system only at prescribed time of the day. This
permits the operator to let the wheel washer turned on and the water heating system activated at night time while the water heating system opera-
tion will be resumed only 1 or 2 hours before workshop opening, thus having the water at the right temperature from the very beginning of operation
while not wasting energy to keep the water warm during the night.
Directions regarding the setup of the timing feature are given further in this manual.
CAUTION
The time needed for taking the water temperature to the set temperature strongly depends on the temperature of the water when the wa-
ter heating system operation is started and may take up to 2 hours when the wheel washer has been just filled with fresh tap water.
•To enable the water heating system press the "WATEr hEATINg sYsTEm" button on the control panel while in the main operation page.
The green LED on the left of the "WATER HEATING SYSTEM BUTTON" will turn on.
CAUTION
If the wheel washer is not equipped with the water heating system, the LCd display will show "No hEATEr" on the first line for a few
41