REMS Power-Press E Instrucciones De Servicio página 12

eng
Pressing power REMS Ax-Press 25 ACC
Pressing power REMS Ax-Press 25 L ACC
Pressing power REMS Akku-Ex-Press Cu ACC
Pressing power REMS Akku-Ex-Press P ACC
REMS Akku-Ex-Press Q & E ACC
REMS Power-Ex-Press Q & E ACC
1.4. Electric Data
REMS Power-Press E,
REMS Power-Press,
REMS Power-Press ACC
REMS Power-Ex-Press Q & E ACC
REMS Akku-Press, Akku-Press ACC
Ax-Press 15/40
REMS Akku-Ex-Press Q & E,
REMS Mini-Press ACC,
REMS Ax-Press 25 ACC / 25 L ACC,
REMS Akku-Ex-Press Cu ACC,
REMS Akku-Ex-Press P ACC
Rapid charger
Li-Ion/Ni-Cd (1h)
Output
Voltage supply 230 V
Output
1.5. Dimensions
REMS Power-Press E
REMS Power-Press,
REMS Power-Press ACC
REMS Mini-Press ACC
REMS Akku-Press / A kku-Press ACC 3 38×290×85 mm (13.3"×11.4"×3.3")
REMS Ax-Press 15/40
REMS Akku-Ex-Press Q & E ACC
REMS Power-Ex-Press Q & E ACC
REMS Ax-Press 25 ACC
REMS Ax-Press 25 L ACC
REMS Akku-Ex-Press Cu ACC
REMS Akku-Ex-Press P ACC
1.6. Weights
REMS Power-Press E drive unit
REMS Power-Press drive unit
REMS Power-Press ACC drive unit
REMS Mini-Press ACC drive unit without battery
REMS Akku-Press / A kku-Press ACC drive unit
without battery
REMS Ax-Press 15 drive unit without battery
REMS Ax-Press 40 drive unit without battery
REMS Akku-Ex-Press Q & E ACC drive unit without batt. 2.0 kg
REMS Power-Ex-Press Q & E ACC drive unit without batt. 5.6 kg (12.2 lb)
REMS Ax-Press 25 ACC drive unit without battery
REMS Ax-Press 25 L ACC drive unit without battery
REMS Akku-Ex-Press Cu ACC drive unit without battery 2.3 kg
REMS Akku-Ex-Press P ACC drive unit without battery
REMS battery Li-Ion 14.4 V, 1.3 Ah
REMS battery Li-Ion 14.4 V, 2.2 Ah
Pressing tongs (average)
Pressing tongs Mini (average)
Pressing heads (pair, average)
Expanding head (average)
Adapter tong Z2
Adapter tong Z4
Adapter tong Z5
Pressing ring M54 (PR-3S)
Pressing ring U75 (PR-3B)
1.7. Noise information
Emission at workplace
REMS Power-Press E
REMS Power-Press /
Power-Press ACC
REMS Mini-Press ACC
REMS Akku-Press, Akku-Press ACC L
REMS Ax-Press 15/40
REMS Ax-Press 25 ACC / 25 L ACC L
REMS Akku-Ex-Press Q&E ACC
REMS Power-Ex-Press Q&E ACC L
REMS Akku-Ex-Press Cu ACC
REMS Akku-Ex-Press P ACC
1.8. Vibrations
Weighted effective value of acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
230 V 1~; 50 – 60 Hz; 450 W; 1.8 A
S3 15% (AB 2/10 min)
all-insulated (73/23/EWG)
interference-suppressed (89/326/EWG)
14.4 V =; 2.2 Ah; 20 A
14.4 V =; 1.3 Ah; 18 A
14.4 V =; 2.2 Ah; 20 A
Input 230 V~; 50 – 60 Hz; 65 W
10.8 – 18 V – ---
Input 230 V~; 50 – 60 Hz
14.4 V – ---; 6 A – 33 A
430×110×85 mm (16.9"×4.3"×3.3")
365×235×85 mm (14.4"×9.2"×3.3")
288×260×80 mm (11.3"×10.2"×3.1")
330×320×85 mm (13"×12.6"×3.3")
290×260×80 mm (11,4"×10,2"×3,1")
420×245×81 mm (16,5"×9,6"×3,2")
295×260×80 mm (11,6"×10,2"×3,3")
325×260×80 mm (12,8"×10,2"×3,1")
265×260×80 mm (10,4"×10,2"×3,1")
275×260×80 mm (10,8"×10,2"×3,1")
4.4 kg
4.6 kg (10.0 lb)
4.6 kg (10.0 lb)
2.1 kg
3.8 kg
4.6 kg (10.0 lb)
5.4 kg (11.8 lb)
2.6 kg
2.8 kg
2.0 kg
0.3 kg
0.5 kg
1.8 kg
1.2 kg
0.3 kg
0.2 kg
2.0 kg
3.6 kg
3.8 kg
3.1 kg
2.7 kg
L = 76 dB L = 87 dB
pA WA
L = 81 dB L = 92 dB
pA WA
L = 73 dB L = 84 dB
pA WA
= 74 dB L = 85 dB
pA WA
L = 74 dB L = 85 dB
pA WA
= 73 dB L = 84 dB
pA WA
L = 73 dB L = 84 dB
pA WA
= 81 dB L = 92 dB
pA WA
L = 73 dB L = 84 dB
pA WA
L = 73 dB L = 84 dB
pA WA
< 2,5 m/s² K = 1,5 m/s²
20 kN Attention: The indicated weighted effective value of acceleration can differ during
13 kN operation from the indicated value, dependent on the manner in which the device
20 kN is used. Dependent upon the actual conditions of use (periodic duty) it may be
20 kN necessary to establish safety precautions for the protection of the operator.
20 kN
2. Preparations for Use
34 kN
The respective latest sales literature applies for the use of REMS pressing
tongs, REMS pressing tongs Mini, REMS pressing rings, REMS adapter tongs,
REMS pressing heads and REMS expanding heads for the different pipe
connection systems. If the system manufacturer alters components of pipe
connection systems or markets new ones, their current application status must
be enquired about at REMS (Fax +49 7151 17 07 - 110).
2.1. Electrical connection
WARNING
the rapid charger, check whether voltage on the rating plate matches the mains
v oltage. At work sites, in damp surroundings, in the open or in the case of
comparable types of use, only operate the equipment off the mains using a
30 mA fault current protected switch (FI breaker).
Rechargeable batteries
NOTICE
Always hold the battery upright when inserting it in the drive unit or
the rapid charger. If inserted at an angle it can cause damage to the contacts
and result in a short circuit which damages the battery.
The rechargeable battery supplied with REMS drive units and spare recharge-
able batteries are not charged. Charge the battery before use. Only use a
REMS rapid charger for charging. The rechargeable batteries only reach their
full capacity after being charged several times. Li-ion batteries should be
recharged regularly in order to avoid their total discharge. The rechargeable
battery will be damaged by exhaustive discharge. Non-rechargeable batteries
may not be charged.
Rapid charger Li-ion/NiCd (Art. No. 571560)
The left control lamp lights up and remains green when the mains plug is
plugged in. If a battery is inserted in the rapid charger, the green control lamp
flashes to indicate that the battery is charging. The green light stops flashing
and remains on to signal that the battery is fully charged. If the red control lamp
flashes, the battery is defective. If the red control lamp comes on and remains
on, this indicates that the temperature of the rapid charger and / or the battery
is outside the permissible range of +5°C to +40°C.
(9.6 lb)
NOTICE
The rapid chargers are not suitable for outdoor use.
2.2. Installing (changing) the pressing tong, pressing tong Mini (1), the pressing
ring with adapter tong (Fig. 18) in radial presses (Fig. 1, 16 and 17)
(4.5 lb)
Pull out the mains plug or remove the battery. Only use pressing tongs, pressing
tongs Mini or pressing rings with system-specific pressing contour according
(8.3 lb)
to the pressfitting system to be pressed. Pressing tongs, pressing tongs Mini
or pressing rings have letters on the pressing jaws or pressing segments to
identify the pressing contour and a number to identify the size. Read and follow
(4.4 lb)
the installation and assembly instructions of the system manufacturer. The
REMS adapter tongs are also identified by a letter and a number. This identi-
(5.6 lb)
fication serves to assign them to the permissible REMS pressing ring. Never
(6.1 lb)
use non-matching pressing tong, pressing tong Mini, pressing ring and adapter
(5.0 lb)
tong (pressing contour, size). The press joint could be rendered useless and
(4.3 lb)
the machine and pressing tong, pressing tong Mini, pressing ring and adapter
(0.6 lb)
tong could be damaged.
(1.1 lb)
(3.9 lb)
It is best to place the drive machine on a bench or on the floor. The pressing
(2.6 lb)
tong, pressing tong Mini or adapter tong can only be installed (changed) when
(0.6 lb)
the press rollers (5) are fully retracted. If necessary, in the case of the REMS
(0.4 lb)
Power-Press E, set the rotation direction lever (7) to the left and operate the
(4.8 lb)
inching switch (8), and in the case of the REMS Power-Press and REMS Akku-
(7.8 lb)
Press press the reset button (13) until the press rollers (5) are fully retracted.
(8.2 lb)
Open the tongs shank (2). To do so, press the locking pin (4), the tongs shank
(6.7 lb)
(2) jumps out under spring loading. Insert the selected pressing tong, pressing
(5.9 lb)
tong Mini (1) or adapter tong (19). Push forward the tong retaining bolt (2) until
the locking pin (4) snaps into place. Press down the pressure plate (3) directly
over the tong retaining bolt. Do not start radial presses without pressing tong,
pressing tong Mini or pressing ring with adapter tong inserted. Only start the
K = 3 dB
pressing process to make a press joint. Without pressing counterpressure by
the press fitting the drive machine or pressing tong, pressing tong Mini, pressing
K = 3 dB
ring and adapter ring will be exposed to unnecessarily high stress.
K = 3 dB
K = 3 dB CAUTION Never operate press when the tongs shank (2) is not locked.
K = 3 dB
Risk of fracture!
K = 3 dB
K = 3 dB 2.3. Installing (changing) the pressing heads (14) in axial presses
K = 3 dB (Figs. 6, 7, 10)
K = 3 dB Remove the battery. Only use system-specific pressing heads. REMS press i ng
K = 3 dB heads have a letter to identify the compression sleeve system and a number
to identify the size. Consult and comply with the instructions for installation and
fitting of the system's manufacturer. Never use non-matching pressing heads
(compression sleeve system, size) for pressing work. The press joint could be
unserviceable, and both the machine and the press i ng heads might be damaged.
Push the selected pressing heads (14) right in, if necessary turning them until
they engage (ball catch). Keep the pressing heads and locating hole inside the
pressing device clean.
Note the mains voltage! Before connecting the drive unit or
eng