Tabla De Contenido; Thanks For Choosing Toto; Included Parts; Common Tools Needed - Toto CST412MF Manual De Instrucciones

TABLE OF CONTENTS
Thanks for Choosing TOTO ® ! .................................................................................................................................................................2
Included Parts ..........................................................................................................................................................................................2
Common Tools Needed ..........................................................................................................................................................................2
Before Installation ................................................................................................................................................................................ 2-3
Installation Procedure .......................................................................................................................................................................... 3-4
Toilet Tank Fill Valve Instructions ............................................................................................................................................................5
Warranty....................................................................................................................................................................................................6

THANKS FOR CHOOSING TOTO!

The mission of TOTO is to provide the world with healthy, hygienic and more comfortable lifestyles. We design every product
with the balance of form and function as a guiding principle. Congratulations on your choice.

INCLUDED PARTS

Check to make sure you have all these parts from the package:
Vitreous China Bowl Modular Rough In
Screw & Washer
for Mounting
Top Mount Bolt Set
Block Installation
(for seat)
(4 pieces each)
(Not pictured but also included: Socket Template)

COMMON TOOLS NEEDED

• 12" pipe wrench • Screwdriver
• 10" adjustable wrench • Putty Knife
• Carpenter's Level • Drill
• Tape Measure • Pliers
MATERIALS REQUIRED:
• Flexible Supply Tube / Connector
• Mounting (T) Bolts & Nuts (2pc)
• Supply Stop Valve • Wax Ring / Seal

BEFORE INSTALLATION

„ Read these instructions thoroughly before beginning work.
„ Please leave instructions for customers. These instruction contain maintenance and warranty information.
„ If necessary, remove the existing toilet.
IMPORTANT!
Due to the powerful performance of our Cyclone, G-Max, E-Max and Power Gravity flushing systems, they are not specified for back-to-back
installations. The only means of installing these toilets in a back-to-back situation is when the toilet drain connections incorporate a WYE fitting.
Please contact your builder or contractor prior to this installation.
Double Combination WYE / 1/8 Bend
YES
Socket
(for 412, 416 & Mounting Block
White Anchor
464 models) (2 pieces)
(4 pieces)
Side Screw and
Side Screw Cap for
Screw with Washer
Mounting Block
Green Anchor
(2 pieces)
(2 pieces each)
(2 pieces)
• For wood floor installation:
- 3/32" drill bit for Modular Rough In
- 11/64" drill bit for Mounting Block
• For concrete/tile installation:
- 9/32" drill bit for Modular Rough In
- 11/32" drill bit for Mounting Block
Double Sanitary Tee / Sanitary Cross
NO
2
Before Installation (continued)
In order for your new TOTO ® toilet to fit correctly, please check the following dimensions:
1) Distance between finished wall and the center of the
floor drain, "RI", must be 12" (305mm) or 10" (254mm)
for CST412MF.10.
2) Water supply should be approximately 8" to 10" to
the left (facing the bowl) from the center line of closet
flange, and approximately 6" above the finished floor.
3) Using the provided template, confirm the installation
dimensions of the PVC trap and the mounting blocks.
Finished Wall
C/L
Supply
Valve
Closet
"RI" Flange
INSTALLATION PROCEDURE
1) Place the installation template so that the baseline of the template and the center line of the closet flange line up. Mark the screw loca-
tions for the PVC trap and mounting blocks. Drill 11/64" screw holes at the marked locations, unless the toilet is being installed on a tile
or concrete floor. In the case of tile or concrete floor installation, drill 5/16" inch holes and use the provided plastic anchors.
2) Clean any debris out of the closet flange, then install the mounting bolts into the slot of the flange head
down with the threaded shank of the bolt pointed upward as shown (Ill. 1).
3) Turn the PVC outlet connection upside down. Firmly press a new wax seal onto the circular recess around
the outlet opening. Turn the outlet connection upright and lower it onto the position over the closet
flange. With the unit properly aligned, press down firmly to set the wax seal.
CA UTION: Do not move the outlet connection after the wax seal is set.
4) Install a washer and nut on the T-bolt to secure the PVC trap to the flange
(see Ill. 2). Nut should be tightened 1/2 turn after hand-tightening. Secure
the back side of the PVC trap to the floor using the provided screws. Level
the PVC outlet. DO NOT USE EXCESSIVE FORCE. Install the mounting
blocks using the provided screws, washers, and anchors. Ensure that
blocks are firmly connected to the floor. If necessary, use the provided
template for the proper alignment.
With the location properly marked, drill holes.
For wood floor installation:
• 3/32" for Modular Rough-In
• 11⁄64" for Mounting Blocks
For concrete/tile installation:
• 9 ⁄32" for Modular Rough In using green anchors
• 1 1⁄32" for Mounting Block using white anchors
To prevent water and odor leakage, please ensure
that the wax seal is fitted properly between the
CAUTION
socket and flange. Do not overtighten the nuts, as
damage to the plastic parts may result.
5) The tank mounting hardware is included
in the tank. Remove the warning sticker
from the bowl. Install the mounting
hardware to the bowl as shown (see Ill. 4).
The mounting hardware is included in the
TS810DV2 bag.
Ill. 4
6) Put the outlet of the toilet bowl to the
mouth of the PVC outlet, then slide the
water closet into socket until it reaches
the wall (see Ill. 5).
In order to prevent leakage,
be sure to insert the toilet all
CAUTION
the way into the socket.
A: Represents dimension 2-½" (63mm)for
mounting blocks for CST412MF, CST-
412MF.10, CST416M & CST464MF.
B
6-3/8" (160mm)
B: 7-7/8" (200mm) for CST412MF, CST412MF.10
& CST416M.
7-1/2"
8-½" (215mm) for CST464MF.
(190mm)
C: 3-3/8" (85mm) for CST412MF & CST416M.
3-½" (88mm) for CST464MF
1-¾" (45mm) for CST412MF.10
6" (152mm)
Ill. 1
Ill. 2
Wax Seal
(not included)
Ill. 3
*CST412
CST416
*CST414
CST464
Rough in
Rough in
Ill. 5
*CST412
CST416
CST464
*CST414 12" (305mm) or
10" (254mm) for
CST412MF.10
3