Installation Procedure; Important - Toto CST412MF Manual De Instrucciones

Installation Procedure (continued)
7) Install the side screws to the mounting blocks. Cover the screw head
with the provided screw-cap (see Ill. 6).
IMPORTANT: If the side screw does not hit the mounting blocks, then
the toilet bowl is not fully inserted in the socket.
If the toilet is not installed properly, it may
slide out of socket or leak.
CAUTION
Please ensure that both sides are properly
fitted and secure. Be sure not to over-tight-
en the screws, as it may results in product
damage.
8) Connect the water supply to the fill valve. The water supply must
be connected to the fill valve BEFORE the tank-to-bowl installation.
TOTO recommends using a flexible supply hose (see Ill. 7).
CAUTION! Do not over-tighten the coupling nut. Only turn it a quarter
turn max after hand-tightening.
Please be sure to connect the water supply
to the fill valve before installing the tank to
CAUTION
the bowl. If procedure is reversed, the water
supply installation may be impossible.
FAILURE TO FOLLOW THIS INSTRUCTION
MAY RESULT IN PERSONAL INJURY AND/
OR PROPERTY DAMAGE.
9) Make sure the fill valve nut and flush valve nut are tightened properly.
Install the tank to the bowl gasket over the flush valve outlet on under-
side of the tank (see Ill. 8).
Pick up the tank and carefully guide the flush valve outlet into the
bowl inlet on the bowl tank-shelf. Make sure the bolts on the bowl fit
through the opening in the base of the tank.
10) For easy assembly, remove the top-portion of the flush valve by
disconnecting the refill tube, turning the upper portion of the valve
counter-clockwise, and pulling up (see Ill. 9). Insert the rubber washer
then metal washer on the mounting bolt. Thread on the nuts, hand-
tighten before releasing the tank. Tighten the nuts evenly until tank
sets snugly on the bowl. Re-install flush valve and refill tube.
Do not over-tighten the mounting bolt.
Over tightening may result in product
CAUTION
breakage and cause personal injury and/or
property damage.
11) Connect the opposite end of the water supply tube to the angle stop.
Open the supply valve and flush the toilet several times. Carefully
check all the connections for leaks. Periodically check for leaks several
days following the installation.
12) Carefully place the lid on top of the tank, making sure that the push
rod colors match the flush valve buttons (blue to blue and white to
white).
To replace or readjust the push rod height, push down on one button
while pulling the opposite button up with your finger to remove it. Use
the provided longer push rod, and insert them through the push but-
ton housing. Cut the push rod at the shown location (see Ill. 11). Install
the rods into the push buttons, and insert the buttons in the housing
until they click into place.
13) The toilet seat is installed with the top-mount bolt set. Insert the rub-
ber bushing-nut into the seatmounting holes. Place the seat on the
bowl and rotate the hinge unit into place while holding the seat down
on the bowl. Tighten the bolt from the top with the screwdriver.
Ill. 6
Ill. 8
Ill. 7
Ill. 9
Ill. 10
Ill. 11
Left
Half Flush
Cut this portion
Ill. 12
Seat Bolt
Rubber Brushing Net
4
1) Shut off the water supply. Flush the toilet, the sponge any
remaining water from the tank. Remove the old fill valve.
2) Slide the threaded valve-shaft through the hole in the bot-
tom of tank.
3) Install the valve in the unlock position, and lock it after
water-line adjustment as shown in Ill. 1. Remove the white
locking clip to unlock the fill valve. Thread mounting nut
onto exposed shaft under the tank and tighten nut.
WARNING! Do not over-tighten.
Gasket
4) Connect the water supply (see Ill. 2). Pipe dope is not rec-
ommended. Attach the refill tube to the valve and clip the
other end to the overflow pipe.
1) Remove the tamper proof key and turn the upper half of the
valve counter-clockwise to unlock it. Pull up the valve and set it
to the desired water level, then turn it clockwise until the valve
snaps into the locked position.
2) Turn on the water supply.
N OTE: The tamper proof key is optional and may be used to
prevent further adjustment (see Ill. 2).
1) Turn off the water supply, then flush the toilet.
2) Snap off the blue cover.
3) Gently press the float arms inward and remove the float.
4) While holding the valve with one hand, twist the cap 1/8 turn
counter-clockwise and remove it.
5) Lift out the center tube as shown in Ill. 4.
6) Remove the strainer from the center tube as shown in Ill. 5. Clean
the strainer and cap by rinsing them off under a faucet.
7) Carefully reassemble the valve in the reverse order.
Right
Full Flush

IMPORTANT:

Note the position of the cap when it's properly assembled to the
body. The ribs on the cap are in line with the float chamber and the
refill port is aligned as shown in Ill. 6.
1) Turn off water supply and flush the toilet.
2) Remove the tank lid and place it upside down on a clean surface.
3) Note the position of the colored button on the flush valve for reassembly.
4) Turn upper half of valve counter clockwise and pull out the flush valve.
5) Remove the clear rubber seal gasket and rinse under running water to clean.
6) Place the gasket back on the flush valve.
7) Install the flush valve back on the base.
8) Rotate the flush valve as needed so the colored buttons are in their original position.
9) Carefully, install the tank lid back on the tank.
10) Flush the toilet several times using each push button to verify proper operation.
Check for leakage.
FILL VALVE INSTRUCTIONS
Installation
Ill. 2
Ill. 1
Lock
Gasket
Unlock
Mounting
Nut
Cone
Seal
Flat Washer
Coupling
Nut
Copper Tube
Water Level Adjustment
Ill. 1
Unlock
Fill Valve Servicing Instructions
Ill. 1 Ill. 2
Ill. 4 Ill. 5
5
Flush Valve Servicing Instructions
5
Ill. 3
Gasket
Tank Wall
Tank Wall
Mounting
Flat Nut
Washer
Coupling
Nut
Flanged
Supply Line
Ill. 2
Lock
Ill. 3
Ill. 6
RIBS IN LINE
WITH FLOAT
REFILL PORT
CHAMBER
RIBS
FLOAT
CHAMBER
Ill. 1
Ill. 2
Ill. 3