Replacing A Fuse; Environmental Protection - Honda HF2315 Manual Del Operador

NOTE
When installing a new spark plug, tighten 1/2 turn
after the spark plug seats to compress the washer. When reinstal-
ling a used spark plug, tighten 1/8 1/4 turn after the spark plug
seats to compress the washer.
IMPORTANT
The spark plugs must be securely tightened. Im-
properly tightened spark plugs can become very hot and may
damage the engine.
6.4.6 Replacing wheels
Stop the machine on a flat surface
and put a block under a load-bear-
ing part of the frame on the side
that the wheel is to be changed.
The wheels are held by a snap ring
(1) which can be eased off with a
screwdriver.
The rear wheels are directly coupled to the axle shaft and fastened
by a key that forms part of the wheel's hub.
NOTE
If you have to replace one or both rear wheels,
make sure they have the same diameter, and check that cutting-
means assembly is horizontal to prevent an uneven cut.
IMPORTANT
Before re-fitting a wheel, smear some grease on
the axle and carefully re-fit the snap ring (1) and washer (2).
6.4.7 Replacing or repairing tyres
The tyres are of the «Tubeless» type and therefore all replacement
or repairs will have to be carried out by a tyre-repair expert in accord-
ance with the methods for this kind of tyre.
6.4.8 Replacing bulbs (in models with lights)
The bulbs (10W) have a bayonet fitting and are installed in the bulb
holder which can be taken out by turning it anti-clockwise, using
pliers.

6.4.9 Replacing a fuse

A few fuses of various capacities are envisaged on the machine.
Their functions and features are given in the following table:
1 - 10 Amps - (Red)
HF23•• •• HF24••
◊
2 - 15 Amps - (Blue)
EN 24
protection of the main circu-
its and power circuits of the
electronic card;
••
◊
protection of the recharge
HF2622H••
2 - 15 Amps - (Blue)
3 - 10 Amps - (Red)
– When the fuse blows (1) the machine stops and all the lights on
the dashboard go out.
– The battery pilot lamp turns on in models provided with it
( 4.11.f) when the fuse (2) trips.
– Tripping of the fuse (3) prevents the control motor of the grass-
catcher's tipping to operate.
IMPORTANT
A blown fuse must always be replaced by one
of the same type and rating, and never with one of another rating.
If you cannot find eliminate the causes of the tripping, consult your
Dealer.
6.4.10 Replacing belts
Replacing belts is quite a complicated process of dismantling and
subsequent adjustment and must only be carried out by your Dealer.
NOTE
Replace the belts as soon as they show obvious
signs of wear! ALWAYS USE GENUINE REPLACEMENT BELTS!

7. ENVIRONMENTAL PROTECTION

Environmental protection should be a priority of considerable impor-
tance when using the machine, for the benefit of both social coexi-
stence and the environment in which we live.
– Try not to cause any disturbance to the surrounding area.
– Scrupulously comply with local regulations and provisions for the
disposal of waste materials after sawing.
– Scrupulously comply with local regulations and provisions for the
disposal of oils, petrol, damaged parts or any elements which ha-
ve a strong impact on the environment; this waste must not be
disposed of as normal waste, it must be separated and taken to
specified waste disposal centres where the material will be re-
cycled.
– At the time of decommissioning, do not pollute the environment
with the machine, hand it over to a disposal centre, in accordance
with the local laws in force.
circuit;
protection of the recharge
circuit;
protection of the grass-catcher
tipping control circuit.