Initial Setup Before Using The Unit - JVC XV-N5SL Manual De Instrucciones

Initial setup before using the unit

We recommend you to set the display language, TV monitor type and digital output before using the unit, by following
the procedure below.
See "Changing the initial settings" beginning on page 48 for details about each setting item.
1
Press CHOICE for a few seconds to bring up
the first page of the DVD PLAYER SET UP
display.
The pull-down menu of the "ON SCREEN
LANGUAGE" is already open.
DVD PLAYER SET UP
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
SELECT USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER
ON SCREEN LANGUAGE options
2
Use 5/∞ to select a desired language.
You can select the on-screen language for the
preference displays, etc. from among English,
Spanish and Chinese.
3
Press ENTER.
The second page is shown, in which the pull-down
menu of the "MONITOR TYPE" is already open.
DVD PLAYER SET UP
MONITOR TYPE
STILL MODE
SCREEN SAVER
MP3/JPEG
SELECT USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER
4
Use 5/∞ to select a desired monitor type.
You can select the monitor type according to your TV.
• For a normal (conventional) TV, select "4:3 LB" or
"4:3 PS."
• For a wide-screen TV, select "16:9 AUTO" or "16:9
NORMAL."
See page 50 for details about each mode.
ENTER
CHOICE
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
CHINESE
SPANISH
4:3 L.B.
16:9 NORMAL
AUTO
16:9 AUTO
4:3 LB
ON
4:3 PS
MP3 16:9 MULTI NORMAL
16:9 MULTI AUTO
4:3 MULTI LB
4:3 MULTI PS
MONITOR TYPE options
TV DVD
STANDBY/ON
OPEN/
TV DVD
CLOSE
TV1 TV2 TV3
1 2 3
TV4 TV5 TV6
4 5 6
TV7 TV8 TV9
7 8 9
TV-/-- TV0 MUTING
10 0 +10
TITLE/ TV/VIDEO
RETURN SUBTITLE GROUP CANCEL
CH
+
5/∞
VOL- VOL+
ENTER
CH
-
PREVIOUS NEXT
CLEAR SELECT STROBE
SLOW- SLOW+
REPEAT SUB TITLE AUDIO VFP
DIGEST ANGLE ZOOM
3D
PHONIC AMP VOL
RM-SXV010U
REMOTE CONTROL
5
Press ENTER.
The third (final) page is shown, in which the pull-
down menu of the "DIGITAL AUDIO OUTPUT" is
already open.
DVD PLAYER SET UP
DIGITAL AUDIO OUTPUT
ANALOG DOWN MIX
D RANGE COMPRESSION
SELECT
ENTER
6
Use 5/∞ to select a desired digital output
signal type.
You must set this item correctly when you connect
the unit to an external surround decoder or D/A
convertor (including an amplifier/receiver with
built-in surround decoder or D/A convertor).
(If you do not connect the unit to such a device, you
do not have to set this item.)
• When connecting with a Dolby Digital decoder,
select "DOLBY DIGITAL/PCM."
• When connecting with a DTS or MPEG
Multichannel decoder, select "STREAM/PCM."
• When connecting with other digital device, select
"PCM ONLY."
See page 51 for details.
7
Press ENTER.
The TV screen returns to showing the opening
display.
NOTES
• This setting may not be necessary except when first
turning on the power after purchasing the unit.
• You can also set these items, as well as other
preferences, by pressing CHOICE briefly to bring up the
preference display. See "Changing the initial settings"
on and after page 48 for details.
Basic operations
DOLBY DIGITAL/PCM
PCM ONLY
DOLBY PROLOGIC
DOLBY DIGITAL/PCM
STREAM/PCM
ON
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
DIGITAL AUDIO OUTPUT options
English
13