Technical Data - Bosch GCM 8 SDE Professional Manual Original

OBJ_DOKU-42126-004.fm Page 29 Monday, November 9, 2015 3:10 PM
56 Clamping screw of the material stop*
57 Adjustment screw for laser position
(parallelism)
58 Stop screw for 0° bevel angle
59 Screw for bevel angle indicator
60 Stop screw for left-hand bevel angle range
61 Stop screw for right-hand bevel angle range
62 Set screws of scale 18 for mitre angles
63 Screw for mitre angle indicator
64 Velcro strap
65 Laser lens cover
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Sliding Mitre Saw
Article number
3 601 M19 ...
Rated power input W
-1
No-load speed min
Reduced starting
current
Laser type nm
mW
Laser class
Weight according to
EPTA-Procedure
01:2014 kg
Protection class
Dimension of suitable saw blades
Saw blade diameter mm
Blade body thickness mm
Max. cutting width mm
Mounting hole mm
diameter
Permissible workpiece dimensions (maximum/minimum) see page 33.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
108 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
Bosch Power Tools
complies with the following standards:
EN 61029-1, EN 61029-2-9, EN ISO 12100, EN 60825-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 03.03.2015
Assembly
 Avoid unintentional starting of the machine. During as-
GCM 8 SDE
... 2.. ... 2B.
Delivery Scope
1600 1400
3500–5000 3500–5000
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
 
– Sliding mitre saw with mounted saw blade
– Material clamp 29
650 650
– Hex key 36
< 0.39 < 0.39
– SDS bolt 51
1M 1M
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
18.9 18.9
be carefully checked to ensure flawless operation of the tool.
/II /II
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
216 216
replaced by an authorised service centre.
1.3–1.8 1.3–1.8
Stationary or Flexible Mounting
3.3 3.3
 To ensure safe handling, the machine must be mounted
30 25.4
Mounting to a Working Surface (see figures A1 – A2)
– Fasten the power tool with suitable screw fasteners to the
or
– Clamp the power tool with commercially available screw
Mounting to a Bosch Saw Stand
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long
workpieces.
 Read all safety warnings and instructions included with
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
on a level and stable surface (e. g., workbench) prior to
using.
working surface. The mounting holes 26 serve for this pur-
pose.
clamps by the feet to the working surface.
the worktable. Failure to observe safety warnings and in-
structions can lead to electrical shock, fire and/or cause
serious injuries.
English | 29
1 609 92A 0Z4 | (9.11.15)