Storage And Transport; Maintenance And Service; Maintenance And Cleaning - Bosch GTS 10 XC Professional Manual Original

Adjusting the level of the table insert (see figure Q)
Checking
The front side of the table insert (32) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table.
Setting
– Remove the table insert (32).
– Use the hex key (37) to set the correct level of the four
adjusting screws (79).

Storage and transport

Storing tool elements (see figures R1–R6)
You can attach certain tool elements to the power tool to
store them.
– Detach the additional parallel guide (52) from the parallel
guide (8).
– Place all loose components of the tool in their storage
compartments on the housing (see the following table).
Fig- Tool element Storage compartment
ure
R1 Protective cover (6) Place in the recess on the
bracket (22) and secure us-
ing the clamping lever (49)
R2 "Additional parallel Clip into the brackets (80)
guide" fastening
set (39)
R2 Dust extraction Slide into the holding
adapter (41) clips (81)
R3 Unused saw blades Place in the saw blade stor-
age compartment (82) and
fasten the cover (14) above it
with the securing nut (12)
R3 Ring spanner (15) Place in the saw blade stor-
age compartment (82) and
fasten the cover (14) above it
with the securing nut (12)
R3 Push stick (13) Attach with the securing
nut (12)
R4 Hex key (37) Slide into the brackets (83)
R4 Parallel guide (8) Place in the parallel guide
storage compartment (36)
R5 Angle guide (3) Slide into the holding
clips (23)
R6 Additional parallel Place in the additional parallel
guide (52) guide storage compartment
and secure with the holding
clip (84)
Transporting the power tool
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position.
– Remove all accessories that cannot be securely fitted to
the power tool.
Bosch Power Tools
If possible, transport unused saw blades in an enclosed
container.
– Slide the saw table expansion (11) in fully and push the
clamping handle (18) downwards to secure it in place.
– Slide the saw table extension (10) all the way in and
tighten the locking screws (38) on the guide bars (24).
– Wrap the power cable around the cable holder (42).
– Use the carrying handles (4) to lift or transport the tool.
Only use the transport devices to transport the power
u
tool and never the protective devices.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Cleaning
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Lubricating the power tool
Lubricant:
SAE 10/SAE 20 engine oil
– Oil the power tool as necessary at the points
indicated (see figure S).
An authorised Bosch after-sales service point will handle this
work quickly and reliably.
Dispose of lubricants and cleaning products in an en-
u
vironmentally friendly manner, taking legal regula-
tions into account.
Noise reduction measures
Measures implemented by the manufacturer:
– Soft start
– Provided with a saw blade specially developed for noise
reduction
Measures implemented by the operator:
– Low-vibration mounting on a stable work surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of the saw blade and power tool
Accessories
Dust bag
Angle guide
Push stick
GTA 6000 saw stand
Saw blades for wood and fibreboard, panels and strips
English | 45
Article number
2 605 411 205
2 610 015 508
2 610 015 022
0 601 B24 100
1 609 92A 7WN | (14.06.2022)