Tabla de contenido
Publicidad
GB
Certificate of Test and Examination after Installation of 600 Model Stairlift to ensure Compliance with
Machinery Directive (2006/42/EC) Low Voltage Directive (2006/95/EC), EMC Directive (2004/108/EC)
Name and Address of User / Installation site: ................................................................ Tel: .......................
1.
Description
Stannah Stairlifts Ltd
a)
Manufacturer:
b)
Stairlift reference number:...................................Chair batch No. ..................................... Carriage batch No...............................
c) Safe Working Load
d)
Rated speed:
e)
Motor tested on assembly:
f)
Control actuator type:
Electrical Tests
2.
a) Electrical supply voltage at time of test:
b) Battery voltage:
c) Functional overload protection test:
d) Tripping time:
e) Control voltage:
f) Mains fuse rating:
3.
Battery Checks
a) Battery charge voltage:
b)
Confirm battery enclosure is vented:
c)
Confirm batteries are securely fitted:
4.
Mechanical / Operation Test
SWITCH OPERATION
a) Confirm all on / off stop switches operate correctly:
b) Confirm all control limits operate correctly:
c) Confirm final limits operate correctly:
d) Confirm all sensitive edges / surfaces operate correctly:
e) Confirm underside sensitive surfaces operate correctly and to the appropriate direction of travel
f) Tests to verify the function of the Overspeed Governor and Safety Gear
g) Confirm that all interlock switches operate correctly (e.g on rotating seat, chair arm isolation etc)
h) Confirm retractable rail safety pad switch stops carriage in down direction
i) Confirm that retractable rail safety arm prevents carriage from clashing with the retractable rail.
j) Confirm that retractable rail clutch slips when manually raised
COMPONENT FUNCTIONING
k) State the stopping distance of the carriage with rated load upon application of the brake:
l) Confirm hand winding controls operate correctly.
m) Confirm Over speed Governor has been subjected to factory test for correct tripping speed:
n) Confirm Installation Overload test has been carried out
o) If an alarm is fitted, confirm mode of operation and that the system operates correctly:
p) Confirm clearance of at least 100mm between chair arms and any part of fixed installation whilst in travel position.
q) Ensure minimum 500mm between adjacent stairlifts during full length of travel
r) Confirm that main entrance and exit doors are not obstructed when stairlift not in use
s) Confirm clearance of 1000mm between seat centre and any height restriction during full length of travel
t) Confirm required hazard warning labels are fitted
u) State distance of footrest above floor level: Not to exceed 170mm
v) State distance of seat above floor level: Not to exceed 650mm
5.
Confirmation
Confirm operating instructions have been handed to the user and the user has been instructed on use of stairlift:
6.
Declaration
We certify that on (DATE) ............................................. this stairlift was thoroughly examined and found to be free from obvious defects
and that the foregoing is a correct report of the results.
Signed: ............................................................... Position / Qualifications: ......................................................
24 to 52 degrees = 160kg (352lbs)
24 to 52 degrees = 135kg (297lbs)
0.1m/s
YES
Constant pressure controls
............V AC
............V DC
YES / NO
......... Seconds
............ Amps
YES / NO
YES / NO
CE Directives:
g)
h)
i)
j)
g) Polarity check:
h) 0-volt rail connected and continuity tested:
i) Confirm battery polarity check:
j) AC supply frequency:
24V DC
k) Phase:
l) Motor reversal delay:
V DC
d)
Confirm batteries are fully charged:
e)
Confirm no leak when battery is fitted:
f)
Confirm off charge indicator is functional:
Siena / Starla Manual and Powered Swivel
Sofia / Solus Manual and Powered Swivel
Model type:
Type of motor:
Motor protection (type):
Type of drive:
L-N = ..........
L-E = ..........
Up............mm
Upper............ mm
Upper ............ mm
600
DC
Electronic
Rack and pinion
N-E = ..........
YES / NO
+ ve ....
- ve ....
............Hz
Single
............ Seconds
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
Down.........mm
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
Lower ............ mm
Lower ............ mm
YES / NO
Publicidad
Tabla de contenido
