Stanley SSC22 Manual De Instrucciones página 20

ENGLISH (
Original Instructions)
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
CHOPSAW SAFETY WARNINGS
♦ Always wear proper eye and respiratory
protection.
♦ Before using, inspect the cutting wheel for cracks
or flaws. If such a crack or flaw is evident, discard
the wheel. The wheel should also be inspected
whenever you think the tool may have been
dropped. Flaws may cause wheel breakage.
♦ When starting the tool with a new or replacement
wheel or if you are unsure of the condition of the
wheel, hold the tool in a well protected area and let
it run for one minute. If the wheel has an undetected
crack or flaw, it should burst in less than one minute.
Never start the tool with a person in line with the wheel.
This includes the operator.
♦ In operation, avoid bouncing the wheel or giving
it rough treatment. If this occurs, stop the tool
andinspect the wheel for cracks or flaws.
♦ Clean your chop saw periodically following the
procedure in this manual.
♦ Do not remove wheel guards or base.
♦ ALWAYS USE THE VISE OR SPECIAL FIXTURE
TO CLAMP WORK SECURELY. Other aids such as
spring, bar, or C-clamps may be appropriate for certain
sizes and shapes of workpiece. Use care in selecting
and placing these clamps and make a dry run before
making a cut.
♦ Use only 14" type 1 wheels rated at 4100 rpm or higher
♦ Allow cut off parts to cool before handling.
♦ Do not attempt to cut wood or plastic with this tool.
♦ NEVER CUT MAGNESIUM WITH THIS TOOL.
♦ Use chop saw in a well-ventilated area.
♦ Turn chop saw off before removing any pieces from the
base.
♦ DO NOT CUT ELECTRICALLY LIVE MATERIAL.
♦ Do not use circular saw blades or any other
toothed blades with this tool.Serious injury may
result.
♦ DO NOT OPERATE THIS TOOL NEAR FLAMMABLE
LIQUIDS, GASES OR DUST. Sparks or hot chips from
cutting or arcing motor brushes may ignite combustible
materials.
20
♦ Do not use the side of the abrasive wheel as a deburring
grinder. This will substantially weaken the wheel
creating an unsafe condition. The wheel may come
apart.
♦ CAUTION! Wear appropriate hearing protection
during use. Under some conditions and duration
ofuse, noise from this product may contribute to hearing
loss.
♦ CAUTION! Spark deflector will get hot. Avoid touching
or adjusting while hot. Keep cordset and materials away
from spark deflector.
♦ Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay
on the skin may promote absorption of harmful
chemicals.
♦ WARNING! Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure.
Direct particles away from face and body. For your
convenience and safety, the following warnings are on
your Heavy-Duty 14" (355mm) Chop Saw:
♦ FOR SAFE OPERATION READ THE INSTRUCTION
MANUAL.
♦ DO NOT USE TOOTHED BLADES.
♦ USE ONLY REINFORCED WHEELS RATED 4100
RPM OR HIGHER.
♦ WHEN SERVICING
REPLACEMENT PARTS.
♦ ALWAYS: WEAR
GUARDS, CLAMP WORK IN VISE, USE PROPER
RESPIRATORY PROTECTION.
♦ DO NOT EXPOSE TO RAIN OR USE IN DAMP
LOCATIONS.
♦ ONLY USE CHOP SAW WHEEL OF A MAX.
THICKNESS OF 3.0MM AND A MAX. DIAMETER
OF 355mm.
LABELS ON TOOL
The label on your tool may include the following symbols:
WARNING! To reduce the risk of injury, the user
must read the instruction manual before use.
Wear ear protection.
Wear safety glasses or goggles.
V Volts
A Amperes
Hz Hertz
W Watts
USE ONLY IDENTICAL
EYE PROTECTION,
Direct Current
n No-Load Speed
0
Class II Construction
Earthing Terminal
USE