Denon CDR-W1500 Instrucciones De Operación página 16

ENGLISH
1. Manual recording
(1) Starting analog recording
(Main unit)
CDR-W1500
PCM AUD O TECHNO OGY / COMPACT D SC RECORDER
UBBIN D SPLAY
T TLE /
8 9 NORMAL H GH IME SELECT CHARACTER
EMO E SE SOR
POWER PHONES PHONES LEVEL
PLAY STOP PAUSE RE AY MODE OPEN CLOSE ON FF
1 2 3 5
M N
1
1
Turn on the power.
2
Load the CD-R/RW disc that is to be recorded.
Perform the operation of "Setup Method (2) Setting the Synchro Recording Mode " on Page 11 and select the Synchro
3
off mode.
When using an already recorded Disc, press the TIME button to check the recordable time.
4
• The time display switches between the total recorded time and the recordable time each time the TIME button is
pressed.
Press the input switching button (INPUT) and select the analog source.
5
• The "ANALOG" display will light.
Perform the operation of "Setup Method" on Page 11 and select on/off of the ATM function.
• ATM Function on
The "ATM" display will light. When a blank portion (of about 3 seconds or longer) of the recording input signal is
6
detected, the track number is automatically associated and recorded.
• ATM Function off
This is recorded as the following track.
7
Start playing the selection you want to record on the CD player, cassette deck, etc.
Press the record button ( REC).
4
8
• The recording standby mode is set.
Adjust the recording level with the jog dial and press the enter button.
• Adjust the input level adjustment control (INPUT LEVEL) so that the "OVER" indicator does not light even when the
volume is loudest. After adjusting, set the source to be recorded to the standby mode.
9
The recording level can be set in advance using the menu mode.
• The set recording level will be stored in memory, but this data might be lost if the unit is not connected to a power
source for 2 to 3 days.
Press the play button ( 1 PLAY).
10
• Recording starts.
11
Start playing the selection you want to record on the CD player, cassette deck, etc.
16
(Remote control unit)
Select the CD-R side.
DUBBING
4 2 8 NORMAL
A ! " A ! "
1
J J （ ）
4
S S . ／
7
[ = ] [ = ]
10
T E CLEAR INPUT F NAL ZE 4 EC 8 9 8
MULTI OG
OPEN CLOSE MENU LAY STOP PAUSE
- + 6
5 1 2 3
MAX
USH
EN ER
8
STOP
2
PROG/DIRECT CALL
10
9 2 5 10
RANDOM
4
D SPL Y EL FADER
5
REMOTE CONTROL UNIT RC-278
(2) Starting digital recording
• This set includes a sampling rate converter.
When recording DATs or satellite broadcasts (32 kHz or 48 kHz) whose digital input signal sampling frequency is different from
that of CD (44.1 kHz), the sampling frequency is automatically converted to 44.1 kHz.
(Main unit)
CD CD R
RELAY
HIGH
MODE
D # % D # % G & ' G & '
2 3
,
M M ＊ ＋ P P −
5 6
V V : ; Y Y ＜ ＞
8 9
PCM AUDIO TECHNOLOGY / COM ACT D SC RECORDER
{ { ? } CLEAR CLEAR
+ 10
DUBB NG
REC
8 9 NORMAL HIGH T ME
7
MENU
LAY TOP PAUSE RELAY MODE
1 2 3
ENTER 9
PLAY
PAUSE
3
1 / ALL A - B
TIME T TLE CHARACTER
NPUT FINALIZE
B
1
Turn on the power.
2
Load the CD-R/RW disc that is to be reco ded.
3
Perform the operation of "Setup Method (2) Setting the Synchro Recording Mode" on Page 11 and select the Synchro off mode.
When using an already recorded Disc, press the TIME button to check the recordable time.
4
• The time display switches between the total recorded time and the recordable time each time the TIME button is pressed.
Press the input switching button (INPUT) and select the digital source (Optical or Coaxial).
5
• The indicator for the selected input source ("CD", "OPT" or "COAX") lights.
Perform the operation of "Setup Method" on Page 11 and select on/off of the ATM function.
• ATM Function on
The "ATM" display will light. When a blank portion (of about 3 seconds or longer) of the recording input signal is detected, the
6
track number is automatically associated and reco ded.
• ATM Function off
This is recorded as the following track.
7
Start playing the selection you want to record on the CD player, MD recorder, etc.
Press the record button (
8
• If the "D. in" indicator is flashing, check the connections to the digital input jacks.
Adjust the recording level with the jog dial and press the enter button.
• Adjust the input level adjustment control (INPUT LEVEL) so that the "OVER" indicator does not light even when the volume is
loudest. After adjusting, set the source to be recorded to the standby mode.
9
The reco ding level can be set in advance using the menu mode.
• The set recording level will be stored in memory, but this data might be lost if the unit is not connected to a power sou ce for 2
to 3 days.
Press the play button (
10
• Reco ding starts.
11
Play the selection to be recorded on the CD player, etc.
NOTES:
• "CD" can be selected by pressing the input selector button, but manual recording from the set's CD unit is only possible in the dual
mode. (Refer to "Dual mode" on Page 26, 27).
• When you do not wish to change the digital recording level, set the jog dial so that "Level 00.0dB" is displayed. The recording
will be made without changing the input signal level.
• The reco ding level can be adjusted over a range of – ∞ to +12 dB for analog input recording and from – ∞ to 0 dB for digital input
reco ding. Note that the displayed setting values may include a degree of error in terms of calculation processing.
• When the recording level is – ∞, "Level---.-dB" is displayed and audio is not output.
Select the CD-R side.
4 2 8
CDR W1500
DISP AY
TIT E /
ELECT CHARACTER T ME CLEAR NPUT FINA IZE 4 EC
RE OTE ENS R
POWER PHONES PHONES LEVEL MUL I JOG
OPEN / CLOSE ON OFF OPEN /CLOSE MENU PLAY
- +
5 5 1
MI AX
P SH
ENTER
1 9 2 5 10
REC).
4
PLAY).
1
(Remote control unit)
CD CD R
DUBB NG RELAY
NORMAL HIGH MODE
A ! " A ! " D # % D # % G & ' G & '
1 2 3
J J （ ） M M ＊ ＋ P P , −
4 5 6
. : ;
S S ／ V V Y Y ＜ ＞
7 8 9
[ = ] [ = ] { ? } CLEAR CLEAR
10 + 10
8
REC
6 7
8 9 MENU
STOP PAUSE
9
8 ENTER
2 3
PLAY
STOP PAUSE
2 3
PROG/D RECT CALL 1 / ALL A - B
10
T TLE
RANDOM TIME CHARACTER
4
D SPL Y SEL FADER INPUT FINALIZE
5
B
REMOTE CONTROL UN T RC-278