Publicidad
Montagevorschriften
Installation tolerances
Tolérances d'installation
Tolleranze dell'installazione
Tolerancias de la instalación
DIMENSIONS, CODE AND TOLERANCE DESCRIPTION (See figure 1)
CODE
A
Variation from nominal dimensions of the clear entry between two uprights at any beam level
Variation from nominal dimensions of the total rack Length, cumulative with the Number of
At
bays "n" measured near floor level.
B
It is the misalignment of opposing rack uprights across an aisle, cumulative with the Number
B
of bays "n" measured near the floor level.
Variation from nominal of rack frontage at the P &D end with regards to the Installation
Bo
"System z Datum Line" concerned, measured near floor level.
Cx
Cx
It is the out of plumb of each upright in the X direction.
Cz
Cz
It is the out of plumb of each upright in the z direction.
D
Variation from nominal dimension of the rack depth (single or double frames).
E
Variation from nominal dimension of the aisle width near floor level.
E1
Variation from nominal dimension of the width between two guide rails.
E2
VNA truck with a bus bar power pick up system.
Variation from nominal of the straightness of an aisle measured near floor level with regard to
F
the "Aisle System X Datum Line" or as specified by the truck supplier.
F1
Variation between adjacent uprights measured near floor level in the z direction
Gz
Straightness of the beam in the z direction
DIMENSIONS, CODE AND TOLERANCE DESCRIPTION (See figure 1)
CODE
Jx
Jx
Upright straightness in the x direction between beams spaced a distance HB apart.
Jz
Initial curve of an upright frame in the z direction.
** H/500 is also an acceptable value for class 300B of the pallet blocks or bearers overhang the front beam by 75 mm. or more and the blocks or bearers are supported on
the beam.
DIMENSIONS, CODE AND DESCRIPTION OF THE TOLERANCE (See figure 1)
CODE
Gy
Gy
Is the straightness of the beam in the Y direction.
H1
H1
Variation of the top of any beam level above the bottom beam level.
Variation of the top of the first beam level from the floor with reference to the system
H1A
datum plane.
Hy
Variation of unit load support levels between the front and rear beams of a compartment.
HORIZONTALS TOLERANCES IN PLANE XZ (mm). RACK UNLOADED
DESCRIPTION
HORIZONTALS TOLERANCES IN PLANE XZ (mm). RACK UNLOADED
DESCRIPTION
VERTIKALE TOLERANZEN IN DER EBENE Y (mm) UNBELADENES PALETTENREGAL
BESCHREIBUNG
27
TOLERANCE ACCORDING TO CLASS OF INSTALLATION
400
Counterba
Reach Truck
Reach Truck
lanced
≤ 9 mt
> 9 mt
± 3
± 3n
The bigger tolerance value of the following
± 20
± 10
The bigger tolerance value of the following
± 10 or
± 10 or
± 10 or
± H/400
± H/600
± H/800
The bigger tolerance value of the following
± 10 or
± 10 or
± 10 or
± H/400
± H/600
± H/800
± 6
± 15
± 15
± A/400
TOLERANCE ACCORDING TO CLASS OF INSTALLATION
400
The larger tolerance value of the following.
± 3 or ±HB/400
± H/500
TOLERANCES ACCORDING TO CLASS OF INSTALLATION
400
The larger tolerance value of the following.
± 3 or ±A/500
The larger tolerance value of the following.
± 5 or ± H1/500
± 10
± 10
300 A&B
± 3
± 3n
±10 or
300A: ± 1.0 n
300B: ± 0.5 n
± 10
± 10 or
± H/800
± 10 or
A : ± H/800
B : ± H/800 **
± 3 / ± 6
double
± 5
+ 5
- 0
± 5
± 10
± 5
300 A&B
± 3 or ±HB/750
300 A&B
± 3 or ±A/500
300A : as for class 400
300B : ± 3 or H1/1000
± 7
± 10
Publicidad
