Additional Information - Pioneer GM-A5602 Manual De Instrucciones

Appendix

Additional information

Specifications
GM-A5602
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
Grounding system ................... Negative type
Current consumption ............ 36 A (at continuous power,
Average current drawn ......... 9.5 A (4 W for two channels)
Fuse ................................................ 30 A × 2
Dimensions (W × H × D) ... 348 mm × 60 mm ×
Weight .......................................... 2.3 kg (Leads for wiring not
Maximum power output ....... 300 W × 2 (4 W) / 450 W × 2
Continuous power output ... 150 W × 2 (at 14.4 V, 4 W,
Load impedance ...................... 4 W (2 W to 8 W allowable)
Frequency response ............... 10 Hz to 70 kHz (+0 dB,
Signal-to-noise ratio ............... 96 dB (IEC-A network)
Distortion ..................................... 0.05 % (10 W, 1 kHz)
Low pass filter:
Cut off frequency ........... 40 Hz to 500 Hz
Cut off slope ..................... –12 dB/oct
Bass boost:
Frequency .......................... 50 Hz
Level ..................................... 0 dB/6 dB/12 dB
Gain control:
RCA ...................................... 0.3 V to 6.5 V
Speaker .............................. 3.0 V to 26 V
Maximum input level / impedance:
RCA ...................................... 6.5 V / 22 kW
Speaker .............................. 26 V / 16 kW
GM-A3602
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
Grounding system ................... Negative type
Current consumption ............ 14.5 A (at continuous power,
Average current drawn ......... 4 A (4 W for two channels)
Fuse ................................................ 25 A × 1
12
En
allowable)
4 W)
15.5 A (4 W for one channel)
215 mm
included)
(2 W) / 900 W TOTAL
(BRIDGE)
20 Hz to 20 kHz, ≦ 1.0 % THD
+N)
450 W × 1 (at 14.4 V, 4 W
BRIDGE 1 kHz, ≦ 1.0 % THD
+N)
225 W × 2 (at 14.4 V, 2 W,
1 kHz, ≦ 1.0 % THD+N)
–3 dB)
allowable)
4 W)
6.5 A (4 W for one channel)
Dimensions (W × H × D) ... 238 mm × 60 mm ×
Weight .......................................... 1.4 kg (Leads for wiring not
Maximum power output ....... 120 W × 2 (4 W) / 200 W × 2
Continuous power output ... 60 W × 2 (at 14.4 V, 4 W,
Load impedance ...................... 4 W (2 W to 8 W allowable)
Frequency response ............... 10 Hz to 70 Hz (+0 dB,
Signal-to-noise ratio ............... 95 dB (IEC-A network)
Distortion ..................................... 0.05 % (10 W, 1 kHz)
Low pass filter:
Cut off frequency ........... 80 Hz
Cut off slope ..................... –12 dB/oct
Gain control:
RCA ...................................... 0.3 V to 6.5 V
Speaker .............................. 3.0 V to 26 V
Maximum input level / impedance:
RCA ...................................... 6.5 V / 22 kW
Speaker .............................. 26 V / 16 kW
Notes
! Specifications and the design are subject to
modifications without notice.
! The average current drawn is nearly the maxi-
mum current drawn by this unit when an
audio signal is input. Use this value when
working out total current drawn by multiple
power amplifiers.
180 mm
included)
(2 W) / 400 W TOTAL
(BRIDGE)
20 Hz to 20 kHz, ≦ 1.0 % THD
+N)
180 W × 1 (at 14.4 V, 4 W
BRIDGE 1 kHz, ≦ 1.0 % THD
+N)
90 W × 2 (at 14.4 V, 2 W,
1 kHz, ≦ 1.0 % THD+N)
–3 dB)