Specific Safety Rules - Metabo PSE 1200 Instrucciones De Manejo

17026834_0806 PSE 1200 NAFTA.book Seite 6 Dienstag, 1. August 2006 1:42 13
ENGLISH
ENG
clothing and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught
in moving parts.
4.3 Avoid accidental starting. Be sure switch is
off before plugging in. Carrying tools with your
finger on the switch or plugging in tools that have
the switch on invites accidents.
4.4 Remove adjusting keys or wrenches before
turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
4.5 Do not overreach. Keep proper footing and
balance at all times. Proper footing and balance
enable better control of the tool in unexpected
situations.
4.6 Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety shoes,
hard hat or hearing protection must be used for
appropriate conditions.
5. Tool Use and Care
5.1 Use clamps or other practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body is
unstable and may lead to loss of control.
5.2 Do not force tool. Use the correct tool for
your application. The correct tool will do the job
better and safer at the rate for which it is designed.
5.3 Do not use tool if switch does not turn it on
or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
5.4 Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool
accidentally.
5.5 Store idle tools out of reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
5.6 Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
5.7 Check for misalignment or binding of
moving parts, breakage of parts, and any other
condition that may affect the tool's operation. If
damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained
tools.
5.8 Use only accessories that are
recommended by the manufacturer for your
model. Accessories that may be suitable for one
tool may become hazardous when used on
another tool.
6
6 SERVICE
6.1 Tool service must be performed only by
qualified repair personnel. Service or
maintenance performed by unqualified personnel
could result in a risk of injury.
6.2 When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unau-thorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.

3 Specific Safety Rules

Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact with a "Iive" wire will also make exposed
metal parts of the tool "live" and shock the
operator.
Before using this power tool, completely read and
understand the enclosed safety information and
the instructions. Keep all enclosed documentation
for future reference, and pass on your power tool
only together with this documentation.
For your own protection and for
the protection of your power tool
pay attention to all parts of the text
that are marked with this symbol!
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Always wear protective goggles, gloves, and
sturdy shoes when working with this tool.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
When sawing water pipes, ensure that they do not
contain any water.
Hold the power tool only at insulated housing
parts if there is any danger of making contact
with concealed electric cables or the supply
cable. Contact with live wires energises the metal
parts of the housing and can cause electric shock
to the operator.
Wear ear muffs when working for long periods
of time. High noise levels over a prolonged period
of time may affect your hearing.
Materials that generate dusts or vapours that may
be harmful to health (e.g. asbestos) must not be
processed.
The dust created when working is often harmful to
health (e.g. when working with oak and beech,
being materials which contain harmful substances)
and should not be allowed to enter your body. Use