Bosch PMF 250 CES Manual Original página 16

OBJ_BUCH-2653-002.book Page 16 Friday, April 1, 2016 12:32 PM
16 | English
12 Handle (insulated gripping surface)
13 Vacuum hose*
14 Vacuum connection
15 Dust extraction*
16 Clamping lever of the dust extraction
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Multi-function tool
Article number
Preselection of orbital
stroke rate
Constant electronic control
Soft starting
AutoClic tool holder
Rated power input
Output power
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Working without auxiliary handle
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-4:
2
Sanding: a =10 m/s , K=1.5 m/s
h
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
2
Scraping: a =12 m/s , K=1.5 m/s
h
Working with auxiliary handle
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-4:
2 2
Sanding: a =9 m/s , K=1.5 m/s
h
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
2
Scraping: a =16 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
1 609 92A 2T0 | (1.4.16)
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
PMF 250 CES
accessories, keep the hands warm, organisation of work pat-
terns.
3 603 A02 1..
Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under "Technical Data" is in conformity with all rele-

vant provisions of the directives 2011/65/EU, until

19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
W 250
complies with the following standards:
W 130
EN 60745-1, EN 60745-2-4, EN 50581.
-1
min 15000–20000
Technical file (2006/42/EC) at:
° 1.4
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
kg 1.2
Henk Becker
Executive Vice President
/II
Engineering
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Changing the Tool
 Before any work on the machine itself, pull the mains
 Wear protective gloves when changing application
2
2 2
=13 m/s , K=2 m/s
h
2 2
=14 m/s , K=3 m/s
h
Please observe the application tools/accessories intended
2
.
for your tool.
Accessory
2 2
=17 m/s , K=2 m/s
h
2 2
=18.5 m/s , K=3 m/s
h
2
.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
plug.
tools/accessories. Contact with the application tool/
accessory can lead to injuries.
PMF 250 CES
Bosch Power Tools