Bosch PMF 250 CES Manual Original página 19

OBJ_BUCH-2653-002.book Page 19 Friday, April 1, 2016 12:32 PM
Mounting/Replacing the Application Tool/Accessory
(AutoClic) (see figures A and B)
If required, remove an already mounted application tool/
accessory.
To do so, open the AutoClic lever 1 all the way. The applica-
tion tool/accessory will be ejected.
Place the application tool/accessory on a flat surface. Press
the power tool onto the application tool/accessory at the re-
quired angle until it can be heard to engage (see illustration on
the graphics page; labelling on the application tool/accessory
can be read from above).
 Check the tight seating of the application tool/acces-
sory. Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
hazard.
Mounting and Adjusting the Depth Stop
The depth stop 10 can be used when working with segment
saw blades.
If required, remove an already mounted application tool/
accessory.
Slide the depth stop 10 over and beyond the tool holder 6 to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
(see indication on the depth stop in large font and not in
brackets).
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Sanding disc Material
– All wooden materials
(e.g., hardwood,
softwood, chipboard,
building board)
– Metal materials
Red quality
– Paint
– Varnish
– Filling compound
– Filler
White quality
Bosch Power Tools
Insert the appropriate segment saw blade for the desired cut-
ting depth. Slide the depth stop 10 from the tool holder 6 in
the direction of the application tool until you can rotate it free-
ly. Rotate the depth stop 10 so that the desired cutting depth
is above the section of the saw blade, which will be used to
saw. Slide the depth stop 10 once again to the stop onto the
gear head of the application tool.
For all other cutting depths and when working with other appli-
cation tools, remove the depth stop 10. For this, remove the
application tool and pull the depth stop from the gear head.
Mounting the Auxiliary Handle (optional accessory)
The vibration-damped auxiliary handle enables the tool to be
used safely and more comfortably.
Screw the auxiliary handle on the right or left of the machine
head depending on the working method.
Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate 8 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 9, free the Velcro backing
of the sanding plate 8 from any debris by tapping against it in
order to enable optimum adhesion.
Position the sanding sheet 9 flush alongside one edge of the
sanding plate 8, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 9, grasp it at one of the tips and
pull it off from the sanding plate 8.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Application
For coarse-sanding, e.g. of rough, unplaned beams
and boards
For face sanding and planing small irregularities
For finish and fine sanding of wood
For sanding off paint
For sanding primer (e.g., for removing brush dashes,
drops of paint and paint run)
For final sanding of primers before coating
English | 19
Grain size
coarse 40
60
medium 80
100
120
fine 180
240
320
400
coarse 40
60
medium 80
100
120
fine 180
240
320
1 609 92A 2T0 | (1.4.16)