Worx Intellicut WG787 Manual De Instrucciones página 14

4) Attach the upper handle (6) with the bolts
and Handle knobs (7) to the lower handle
(8). (See Fig. B3)
5) Screw on the two Handle knobs. Check that
the handle is FULLY secured.
NoTE: Ensure the bolts are fully inserted
through the handles before fitting the handle
knobs.
6) Attach the Cable Clips (2) provided, to the
upper and lower handle. Insert the cable
into the clips ensuring there is enough
cable slack (See Fig. B4).
2. GraSS CoLLECTioN BaG aSSEMBLy
1) Attach the grass bag handle to the grass
bag assembly as shown in Fig C1-C4.
a. Identify the front and rear of both the
handle and the Grass Collection Bag (4)
assembly (See Fig. C1).
b. Insert the front portion of the handle into
position (See Fig. C2).
c. Secure the front portion of the handle in
place by pushing it forward (See Fig. C2).
d. Insert and secure the rear portion of the
handle in position by pushing down on the
14
back of the handle ensuring it "clicks" into
position (See Fig. C2).
2) Clip the plastic clips of the grass bag over
the metal frame (See Fig.C3).
warNiNG: Make sure to not fit the
handle in the reverse direction as it
will not remain secure. Make sure to fit
the handle as shown in Fig C4.
3. aTTaChiNG ThE GraSS CoLLECTioN
BaG (4) To ThE MowEr (See Fig. D1,
D2, D3)
NoTE: The Grass Collection Bag is held in
place by the Safety Flap.
1) Switch the mower off, remove the Safety
Key (5) and wait until the mower Blade (15)
has stopped.
2) Raise the Safety Flap (9) and hold it in the
upward position while the Grass Collection
Bag (4) is properly located below it (See
Fig. D1).
3) Position the lower edge of the Grass
Collection Bag on the plastic tabs (b) found
below the rear discharge chute on the
mower deck (See Fig. D2).
3-in-1 Cordless Lawn Mower
4) While holding the Grass Collection Bag
in position, lower the Safety Flap into its'
final position. It should rest on top of the
Grass Collection Bag with the tabs of the
Grass Collection Bag being inserted into
the Safety Flap. Ensure the Safety Flap
locks securely into position with the Grass
Collection Bag (See Fig. D3).
NoTE: The two parts should smoothly slide
together with little force. They WILL NOT
"click" together.
NoTE: Depress the Grass Collection Bag
slightly to ensure that it is completely installed.
4. rEMoviNG/EMPTyiNG ThE GraSS
CoLLECTioN BaG (4)
1) Switch the mower off, remove the Safety
Key (5) and wait until the mower blade has
stopped.
2) Hold the Grass Collection Bag handle
3) Raise the Safety Flap (9) upward and hold
it in the upward position until the Grass
Collection Bag is removed (See Fig. D1).
warNiNG! Before each use, always
check that the safety flap closes
securely over the rear discharge chute.
Never lift the Safety Flap when the
lawn mower is in operation. The Blade
(15) must be completely at rest before
handling the Safety flap.
5. FiTTiNG/rEMoviNG ThE BaTTEry
PaCK (See Fig. E1, E2, E3, E4)
REMOVING THE BATTERY PACK (10)
1) While gripping the battery handle lift it
upward without twisting or turning it (See
Fig. E1).
FiTTiNG ThE BaTTEry PaCK
1) Locate the front and rear of the battery (See
Fig. E2)
2) Lower the battery into position. (See Fig.
E3)
NoTE: For a secure fit, make sure the battery
tray is free of debris and the contacts on the
Battery Pack and in the battery tray are clean
(use a dry cloth to clean) (See Fig. E4)
NoTE: When fitting or removing the battery be
careful not to drop the battery onto your foot
or the ground.
EN