Electric Connections And Safety - Jacuzzi J Twin Premium Manual De Instalación

(e) and then click it onto the supports themselves (
essary, to straighten up the panel adjust the support screw (e),
after having removed the panel.
I Insert the front panel between the under-edge springs (a), the
corner springs (c) and the tub rim; then click it onto the supports,
referring to the instructions for the side panel (
I At this point, place the white plastic caps onto the visible screw
i
heads ( 26).
J•Sha Active Twin
I Position the brackets according to the instructions given in
i
28.
Check the distance between the tub rim and the brackets, which
must correspond to the dimensions shown.
I Insert the side panel between the corner springs (c and c1)
and the tub rim by pressing it in (use the "1-2" holes to attach the
left panel and the "3-4" holes to attach the right one,
29), making sure that the holes on the side panel line up with the
slots in the brackets; if necessary, to straighten up the panel
i
adjust the brackets ( 28).
I Fasten the panel with the screws shown.
I Insert the front panel between the under-edge springs (a), the
corner springs (c1) and the tub rim by pressing it in (
29); proceed following the instructions given in the previous
stages, including the side panel; to straighten up the panel adjust
the brackets.
I Fasten the panel and attach the white plastic caps to the visible
i
screw heads ( 29).

Electric connections and safety

Connection of the tub to the electric system of the building must
be carried out in compliance with the norms in force.
I The operation must be limited to the passage of the cable and
attachment of the cables to the terminals, making sure not to
damage any of the components. The "phase" cable must be con-
nected to the terminal marked with the letter "L", the "neutral"
cable to the terminal marked with the letter "N" while the "earth"
cable must be connected to the terminal marked with the symbol
(see electric diagrams).
IMPORTANT: for Countries where 220-240V voltage
is supplied by a two-phase system (L+L), the connec-
tion has to be made on terminals L and N anyway.
After connection has been made, the installer must replace the
cover and tighten the cable clamp, in order to guarantee protec-
tion from water jets, as provided for in the norms.
Models with thermostatic mixer
Dismantling and cleaning of the thermostatic valve
The thermostatic valve is provided with mesh filters, to trap pos-
sible impurities in the water; over time, these filters could
i
27); if nec- become blocked and therefore inhibit the function of the mixer
tap; to clean the valve, remove it in this way:
I
I
i
27). the diverter ring (5) on the symbol "water into tub" and open the
stop cock completely (3); however, a little water will remain inside
the brass part). After emptying the mixer unit, close the stopcock
by turning the knob to the previous position.
I
of a screwdriver; be careful not to scratch the knob.
I
(3a).
I
(5).
i
24 and
I
lower part; be careful not to scratch the template and the
methacrylate panel.
I
I
i
24 and
I
present, wash with specific products.
I
dure backwards; also follow these instructions:
- the stopcock knob (3) must be in the vertical position (
- mount the thermostatic valve so that the sprig (9) (screw peg) is
facing downwards, so that it can enter the milled part of the
brass casing (
9
Turn of the water supply (hot and cold) to the shower box.
i
( 30) Drain the water present in the mixer unit by positioning
i
( 30) Remove the caps (1) of the two knobs, by using the tip
i
( 31) Remove the screws (2) and loosen the knobs (3) and
i
( 31) Unscrew the cover (4) and then remove the diverter ring
i
( 32) Remove the template (6) by prizing in the hole on the
i
( 32) Unscrew the the cover (7).
i
( 33) Ease out the thermostatic valve (8).
Clean the mesh filters with a little brush and rinse; if scale is
Reassemble the various components following the same proce-
i
33).
i
30).